463800
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
4 echoInstallationInstructions


1. Feed the cables
through the
5
/
8
in. (16 mm) center hole you drilled
when preparing the swivel-mount base.
2. Place the swivel-mount base
on the
mounting surface, route the cables through
the cable pass-through holes
, and
loosely fasten the swivel-mount base using
the appropriate screws or bolts
.
3. Place the swivel mount
on the swivel-
mount base, but do not fasten it.
4. Place the echo device or cradle into the
swivel mount (page 4).
5. Pull out enough slack from the power and
transducer cables so that the mount can
fully swivel to the desired positions when
the cables are connected.
6. Remove the echo device or cradle, and the
swivel mount, from the swivel-mount base.
7. Apply marine sealant to the
5
/
8
in. (16 mm)
center hole and to the cable pass-through
holes.
8. Securely fasten the swivel-mount base, using the appropriate screws or
bolts.
9. Place the swivel mount on the swivel-mount base, and fasten it using the
included 10 mm M6×1 Phillips screw
.


Complete this task only if you do not need to run the
cables through the mounting surface and the mount.
1. Place the swivel-mount base
on the mounting
surface, and fasten it using the appropriate screws
or bolts
.
2. Place the swivel mount
on the swivel-mount
base, and fasten it using the included 10 mm
M6×1 Phillips screw
.
3. Seal the cable pass-through holes
with marine
sealant.

1. With the locking arm
in the upward position, place the echo
100/150/300c device
or the echo 200/500c/550c cradle
into the
swivel mount
.
2. Tilt the mount for the desired viewing angle and press down on the
locking arm.


1. Route the power cable from the swivel mount to the boat battery or fuse
block.
If necessary, extend the wires using 20 AWG or larger wire.
If you connect the power cable to the fuse block, rst remove the
inline fuse holder on the red wire.
2. Connect the red wire to the positive terminal on the battery or fuse block,
and connect the black wire to the negative terminal.

On an echo 100/150/300c device, the connectors on the cables are keyed to
t only in the correct ports on the device.
1. Compare the divot
on the cable connector to the
keying on the device ports to identify the correct port.
2. Push the cable connector into the correct port until the
connector is fully seated.
3. Repeat steps 1 and 2 until all of the cables are connected
to the device.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin Echo 100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin Echo 100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin Echo 100

Garmin Echo 100 Installatiehandleiding - Nederlands - 6 pagina's

Garmin Echo 100 Gebruiksaanwijzing - Nederlands - 12 pagina's

Garmin Echo 100 Installatiehandleiding - Deutsch - 6 pagina's

Garmin Echo 100 Gebruiksaanwijzing - Deutsch - 12 pagina's

Garmin Echo 100 Gebruiksaanwijzing - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info