502505
5
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
5
CAUTION: The speed control I may be turned only between
numbers 1 and 6. Do not force the control beyond these
positions, otherwise it may break and fail to work.
STARTING THE TOOL
WARNING! The tool should not be in contact with the
surface of the part to be worked on when you start or stop it
- otherwise this could cause defective sanding or damage the
belt. To switch on the tool, pull the trigger switch H. Release
it to turn the tool off. and press the blocking button G. To stop
the tool when blocked, pull the trigger H again and release
it.
WORKING INSTRUCTIONS
To begin sanding, rst hold the tool rmly in both hands.
Switch on the tool and wait until it reaches the required
speed. Then carefully place the tool on the surface of the part
to be sanded. Keep the belt against the work constantly and
move the machine backwards and for-wards without pressing
too hard. Never force the tool.
The weight of the tool is sufcient to give adequate
performance and pressure. Excessive pressure may cause
jamming, overheating of the motor, burning of the part being
sanded and recoil.
Use the right type of belt for the surface being sanded and
the desired results.
CAUTION: Whilst sanding, always keep the lead to the back
of the machine to avoid it getting caught.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying out
work on it.
- Inspect the mounting screws: Regularly inspect all the
mounting screws and ensure they are rmly tightened.
Should any screw be loose, tighten it immediately.
Failure to do so could put you at serious risk.
- Motor maintenance: Never press too hard when using the
sander. Excessive pressure may produce an over-load and
damage the motor or the part being sanded.
- Brush replacement: The brushes disconnect automati-cally
and should be replaced after 150-200 hours’ use or when
they are less than 10 mm long. Have them replaced by an
Ofcial Service Centre.
- To clean the sander thoroughly after use, unplug it from the
mains and use a dry brush to clean all orices.
- The vents of the machine should be kept clear at all times.
Use a clean damp cloth to clean the protective covers (do not
use solvents, petrol or turpentine).
- Check that the mains lead is in good condition. If it is not,
take it to an Ofcial Service Centre to have it replaced.
- Use only FELESATTI accessories and spares. The parts the
changing of which is not covered in this instruction manual,
should be replaced in a FELESATTI Ofcial Service Centre
(See Warranty/Ofcial Service Centre address leaet).
WARRANTY
See general warranty conditions printed on the attached
sheet.
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances
and its translation into national law, used electric
tools must be collected separately and recycled in
an ecologically desirable way.
DECLARATION OF
CONFORMITY
We hereby declare, under our sole
responsibility, that the FELISATTI
brand products described in this
manual comply with the following
standards or standard documents:
EN60745-1:2009, EN60745-2-
4:2009, EN55014-2:1997+A1+A2,
E N 6 1 0 0 0 - 3 - 2 : 2 0 0 6 + A 1 + A 2 ,
EN61000-3-3:2008 in accordance
with EU Directives 2006/42/EC,
2006/95/EC, 2004/108/EC, 2002/96/
EC
Francisco Ruis
Technical director
We reserve the right to make technical changes 06/2011
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Felisatti BSF100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Felisatti BSF100 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info