Présentation de votre lave-vaisselle
49
GB
Présentation de votre lave-vaisselle
48
GB
- Wrongly programmed.
- No salt or too little salt
in the reservoir to trig-
ger the float.
- Insufficient amperage to
supply all the equip-
ment being used at the
same time.
- Internal fault in the
machine
- No power supply to the
socket
- The tap is closed
- The water supply hose
is kinked
- Programme selection
error and programme
blocked
- “Start” button held down
too long (> 2 seconds)
- Safety system (anti-leak)
- Protective cover on the
sink’s U bend not removed
- Drainage hose kinked
- Drain filter totally
blocked
- Pump blocked.
- Cancel the current pro-
gramme by holding
down the “Start” button
for 3 seconds and then
reprogramme.
-
Fill the reservoir and
wait until the cycle
ends. If the water is
soft enough not to
require salt, the Salt
light is permanently lit.
- Check the plug’s ampe-
rage (10A minimum)
and the meter’s capacity
- Call an engineer.
- Check the socket and
the fuse
- Check that the tap is
open
- Check that hose run
- Cancel by pressing
“Start” for 3 seconds
and reprogramme
- Press “Start” only briefly
to start the programme
- Call an engineer.
- Remove the protective
cover
- Check the hose runs cor-
rectly behind the machine
- Remove the filters and
clean them and the
drain hole
- Start a soak programme.
If the fault persists,
call
an engineer.
The lights light up one
after another
The Salt light does not go
out
The machine cuts off
The machine will not
start
The machine does not
drain.
Troubleshooting, what to do?
Programming, display anomalies
Possible causes What to do
Poor operation Possible causes What to do
Troubleshooting, what to do?
If you are in any doubt about the operation of your machine, before calling a qual-
ified engineer, check the following points (depending on the symptoms noticed).
When first using the machine
Possible causes
What to do
- Adjust the adjustable
feet
- Adjust the rear feet
- Take off the door seal
all around the door.
- Check that the seal is pre-
sent and re-tighten the nut
- Close the water tap and
call an engineer.
- Recentre the door by
adjusting the rear feet.
- Contact the installer.
- Tighten the two tensioning
screws accessible through
the holes in the two side
panels
.
- Contact the installer.
- Loosen the two tensioning
screws accessible through
the holes in the two side
panels
.
- Fit a wooden panel to the
door (a chipboard panel OK
if on a temporary basis)
and adjust the springs.
- Contact the installer.
- Move the basket gradu-
ally on one side and
then the other (until
you hear a “Click”) = ->
see the Operating Instructions.
- Use these programmes
preferably at night
when the length and
the finishing time are
not important.
- The machine is wobbly,
not level
- The door is not correct-
ly centred on the tub
-
The seal’s lip has been
flattened during storage.
- Leak at the tap
- Leak in the machine
- The machine or the
door is not correctly
centred on the tub
- The door springs are
not tensioned enough
to compensate for the
weight of the basket.
- The door springs are
over-tensioned.
- No wooden panel
- Poor handling (the bas-
ket has been pulled
upwards too quickly).
- The energy-saving pro-
grammes take longer
because they compensate
for the lower washing and
drying temperatures by
longer agitation and drying.
Small door leak
Small leak around or
under the machine (move
the machine to locate the
leak better)
The door “catches” when
you close it
The door falls down
heavily when you open it
(integratable models)
The door is not level
when open or goes back
up too quickly (integrat-
able machine)
The upper basket will not
stay in the high position
The cycle takes too long.
Programming, display anomalies
Possible causes
What to do
