55632
10
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
10
u Place the chain (6) over the guide bar (7) making sure that
the saw chain cutters on the upper part of the guide bar
(7) face towards the front (fig. B).
u Guide the chain (6) around the guide bar (7) and pull it to
create a loop to one side at the rear end of the guide bar
(7).
u Guide the chain (6) around the drive sprocket (12). Place
the guide bar (7) onto the bar location studs (13) (fig. E).
Warning! Make sure that the front guard/chain brake
assembly (4) is in the set (forward) position before retting
(g. C).
u Before fitting the chain cover assembley check that the
cam (11) (fig. B) is in the correct position. If necessary,
press in and turn the control knob (9) clockwise to rotate
the cam into the correct position.
u Fit the chain cover by locating the bolt and using the
control knob (9) to tighten the chain cover finger tight.
u To tension the chain, loosen the control knob one full turn,
press in firmly and rotate clockwise. As the bar moves
forward make sure that the chain links feed into the guide
bar.
u Allow the control knob to spring back to the „out“ position
and rotate further clockwise to tighten the guide bar. Do
not overtighten.
u Check the tension as described below.
Checking and adjusting the chain tension
(g. G)
Before use and after every 10 minutes of use you must check
the chain tension.
u Disconnect the tool from the mains supply.
u Lightly pull on the chain (6) as shown (inset fig. G). The
tension is correct when the chain (6) snaps back after
being pulled 3 mm away from the guide bar (7). There
should be no "sag" between the guide bar (7) and the
chain (6) on the underside.
Note: Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the guide bar and
the chain.
Note: When the chain is new, check the tension frequently
(after disconnecting from the mains) during the rst 2 hours
of use because a new chain stretches slightly.
To increase the tension
u Loosen the control knob one full turn, press in firmly and
rotate clockwise untill the required tension is reached. As
the bar moves forward make sure that the chain links feed
into the guide bar.
u Allow the control knob to spring back to the „out“ position
and rotate further clockwise to tighten the guide bar. Do
not overtighten.
Use
Warning! Let the tool work at its own pace. Do not overload.
Filling the oil reservoir (g. F)
u Remove the oil cap (3) and fill the reservoir with the
recommended chain oil. You can see the oil level in the oil
level indicator (5). Refit the oil cap (3).
u Periodically switch off and check the oil level indicator (5);
if it is less than a quarter full, disconnect your chainsaw
from the mains supply and refill with the correct oil.
Switching on
Note: It will not be possible to switch the tool on if the
front guard/chain brake assembly is not in the "set"
position.
u Grip your chainsaw firmly with both hands. Push the
lock-off button (2) and then push the on/off switch (1) to
start.
u When the motor starts, remove your thumb from the lock
button (2) and grip the handle firmly.
Do not force the tool, allow the tool to do the work.
It will do a better and safer job at the speed for which it is
designed. Excessive force will stretch the saw chain (6).
How to set the chain brake (g. C)
u Make sure that the tool is disconnected from the mains
supply.
u Pull the front guard/chain brake assembly (4) back into the
"set" (fig. C) position.
u The tool is now ready to use.
How the anti-kickback chain brake works
In the event of kickback, your left hand comes in contact with
the front guard, pushing it forwards, toward the workpiece,
and stops the tool within a few fractions of a second.
How to test the anti-kickback chain brake (g. C)
u Always check that the kickback brake operates correctly
before use.
u Grip the tool firmly in both hands on a firm surface make
sure the saw chain (6) is clear of the ground and switch on
(see" How to switch the chainsaw on").
u Rotate your left hand forward around the front handle so
that the back of your hand comes in contact with the front
guard/chain brake assembly (4) and push it forwards,
toward the workpiece (fig. C). The saw chain (6) should
stop within a few fractions of a second.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Black-Decker-GK1630T

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GK1630T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GK1630T in de taal/talen: Engels als bijlage per email.

De handleiding is 1,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker GK1630T

Black Decker GK1630T Gebruiksaanwijzing - Nederlands - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Nederlands - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Deutsch - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Deutsch - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - English - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - English - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Français - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Français - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Italiano - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Italiano - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Português - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Português - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Espanôl, Espanõl - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Espanôl, Espanõl - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Dansk - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Dansk - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Svenska - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Svenska - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Norsk - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Norsk - 104 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Suomi - 128 pagina's

Black Decker GK1630T Gebruiksaanwijzing - Suomi - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info