772318
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
1ATTACH MOUNT ONTO BIKE FRAME
1. Remove four (4) screws from back of
mount using 5mm Allen wrench.
2. Place front of mount around seat
tube of bike. Insert back of mount
to front of mount, insert screws.
Do not fully tighten. Do not place
around brake and derailleur cable
and housing.
CLICK RACK INTO MOUNT
1. Slide the ends of the carrier rack into the top holes on the mount. Once secured,
you will hear a click. This means the carrier rack is secured to the mount.
2. Slide the loose mount up or down until there is about 6 inches between rear wheel
and bottom of carrier. Be sure mount is centered along rear wheel facing forward.
3. Tighten the screws on the mount until mount will not slip up, down, or side to side.
4. Tighten fasteners securely, and check them frequently.
2
3
EASY, 3-STEP INSTALLATION
WARNING
Do not modify carrier rack or bicycle. If carrier rack will not t on your bicycle, consult your local bicycle dealer or
call our Customer Service at 1.800.456.BELL for assistance.
SEAT PAD INSTALLATION FOOT REST INSTALLATION
FOOT STRAP ATTACHMENT
1. Loop one piece of Velcro® through each foot rest and
attach back onto itself.
2. Insert top hooks of foot rests into opening along leg. Must
be at least three notches from bottom. Push to lower tabs
through respective opening and click into place. Lower
hook tabs need to be slightly lifted when inserted into slot.
Place seat pad into bottom of child carrier. Thread retention
harness through seat pad. Insert all four seat pad plugs into the
bottom of the child carrier.
To insert foot rest, insert top hook into preferred height. Slide
bottom tab into slot and pinch both together at the same time
while pushing the foot rest into place. Pull at them gently to
ensure they are secured properly. To remove foot rest, pinch
the hook and tab at the same time and pull up, freeing the
bottom tab. Then pull the top hook free.
Use harness slots at
child’s shoulders.
Shoulder straps should t snugly –
so that only one nger can t
between harness and shoulder.
Ensure top of chest clip is
positioned at armpit level.
Ensure harness forms the
shape of a V.
Connect each buckle end and
click to secure.
To release, pinch each side
of buckle and pull apart
buckle ends.
WARNING
Child can fall out of child carrier if harness is not correctly
fastened and adjusted.
RETENTION HARNESS:
3-POINT HARNESS
REFLECTOR INSTALLATION
To install the reector, remove backing paper on the reector
and place the sticky side onto the hexagonal molded imprint on
the back center of the child carrier. Press to adhere.
4 | English 5 | English
ATTACH RACK TO CARRIER
1. Turn the carrier upside down. Insert
suspension rack bars through holes
as shown below.
2. Insert the locking pin through the
holes under the carrier with the lever
in the unlocked position until it snaps
into place.. Turn the pin 180 degrees
untill it snaps into the locked position.
1
2
UNLOCKED LOCKED
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bell Shell bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bell Shell in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 2.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info