713911
20
Verklein
Vergroot
Pagina terug
1/220
Pagina verder
Adjusting the wheel alignment
Important: To achieve the very best movement, the rear wheels must be
adjusted to their optimum position, which means correctly adjusting the wheel
alignment.
To do this, measure the distance between both wheels front and rear to
ensure that they are parallel to one another. The difference between both
measurements should not exceed 5 mm.
To adjust the wheels to make them parallel, loosen the screws and turn the
axle sleeve accordingly. Make sure that after any adjustment work, all screws
are tightened correctly (see the page on torque).
SIMBA tracking adjustment
Setting the toe-in/toe-out to zero:
NOTE: A wheelchair with 0° camber cylinders cannot have toe-in or toe-out.
This setting is necessary only with 3°, 6° and 9° camber cylinders.
The term "toe-in or toe-out" defines how well the rear wheels of the chair are
aligned in relation to the ground. This determines how well the chair will run.
Normal resistance or rolling resistance is present when toe-in is set to zero.
To set toe-in/toe-out to zero: Loosen the Allen screws (1) (one on each side),
which secure the angle tube clamp. Check the ball in the horizontal (2) plane
and turn the angle tube (3) until the ball is in the centre. Toe-in is now zero.
Before tightening the screws (1), check that the camber tube is centred left-
to-right. The gap should be the same on both sides, or there should be no
gap at all. Tighten the screws to 10 Nm (Fig. 5.14 - 5.16).
Wheel Alignment
Adjusting the wheelbase width
CAUTION!
When adjusting the rear wheelbase, adjust first one wheel then the other.
If both sides are loosened at the same time, this will alter the toe-in/toe-out
adjustment. To adjust the rear wheelbase, the parts of the camber (4) move
telescopically into or out of the camber tube (5), and lock into place when
they reach the end. Loosen screw (6) (located closest to the camber tube) on
the left side of the chair.
Move the quick-release axle inwards or outwards to achieve the desired
wheelbase. Tighten the screws to 10 Nm. Repeat this procedure on the right
side of the chair and adjust the gap so that it is the same amount as on the
left side (Fig. 5.17).
CAUTION!
The screws/bolts used on this wheelchair have thread locking fluid applied at
the factory. After that they should be replaced or alternatively re-secured with
threadlock to medium tightness.
Fig. 5.14
1
Fig. 5.17
5
6
4
Fig. 5.15 Fig. 5.16
Ball
2
3
20
Rev.6.0
Simba
ENGLISH
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zippie Simba bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zippie Simba in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info