713911
19
Verklein
Vergroot
Pagina terug
1/220
Pagina verder
Castor, Castor adapter, Castor fork
From time to time the wheelchair may veer slightly to the right or left or the
castors may flutter.
This may be caused by the following:
• Forward and/or reverse wheel motion has not been set properly.
• The castor angle has not been adjusted properly.
Castor and/or rear wheel air pressure is incorrect; wheels do not turn smoothly.
The optimum adjustment of the castors is required so that the wheelchair runs in
a straight line.
Castors should always be adjusted by an authorised dealer. The castor plates
must be readjusted, and the wheel locks must be checked any time the rear
wheel position has been altered.
Adjusting the castor
To ensure that both forks are set parallel, simply count the teeth visible on both
sides. After setting the castor fork, the teeth will guarantee a secure position,
allowing an adjustment of 16° in 2° increments. Use the flat side to check for a
right-angled position to the ground.
The patented design allows the castor fork to be turned, so that it can be reset at
right-angles to the ground when the seat angle is changed (Fig. 5.10 + 5.11).
Setting the directional stability
Release the Allen screws (1) on the underside of the fork. You can then undo the
screw (2). You can now turn the black socket (3) left or right.
Left – chair pulls to the left
Right – chair pulls to the right
Then tighten up the screw (2) again. Please set a 90° angle from the fork to the
floor.
Now tighten up the screw (1) again. (Fig. 4.16).
CAUTION!
The screws/bolts used on this wheelchair have thread locking fluid applied at
the factory. After that they should be replaced or alternatively re-secured with
threadlock to medium tightness.
Castor
Adjusting the seat height
To adjust the rear seat height release and remove the Allen screw (1) (one on
each side), that fixes the clamp, (2) to the axle plate. Adjust the two camber
tube clamps (2) to the required height and replace the two Allen screws. Before
tightening the screws, please follow the instructions for setting the toe-in/toe-out
to zero.
Tighten the screws to 10 Nm. (Fig. 5.13)
CAUTION!
An adjustment to the castor angle may be necessary when adjusting the rear
seat height.
The screws/bolts used on this wheelchair have thread locking fluid applied at
the factory. After that they should be replaced or alternatively re-secured with
threadlock to medium tightness.
Seat
Fig. 5.10
Fig. 5.11
90
o
Fig. 5.12
1
2
3
Fig. 5.12
Fig.5.13
1
2
19
Rev.6.0
Simba
ENGLISH
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zippie Simba bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zippie Simba in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info