478506
14
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
Page 12 VL-1000 Operating Manual
Drive Power Check
If this is first-time operation, or whenever
using a different exciter (transceiver), perform
this procedure to check peak exciter driving
power.
Turn the VL-1000 POWER switch on by
pressing the switch in.
Make sure that the OPERATE and TUNER
switches on the VL-1000 are both off.
Connect a 100-watt dummy load to the ANT
1 jack on the VL-1000, if available. If a
dummy load is not available, connect an
antenna which presents a 50 Ω resistive
load to the ANT 1 jack. Tune your exciter to
a clear frequency.
Set the transceiver to the CW mode, and
preset the D
RIVE or RF PWR control on the
transceiver fully clockwise (maximum).
Briefly key the transmitter, while watching
the display of the VL-1000. If the (indicated)
exciter power is above 100 watts, turn the
ATT switch ON. Never press the ATT
switch while transmitting.
Drive power must be at least 50 watts for
accurate SWR detection, and 70 to 80 watts
for optimum tuner performance. Full power
output will be obtained from the VL-1000 when
the drive power is between 50 and 80 watts,
depending on the band in use. When the VL-
1000 power amplifier section is activated, ALC
voltage is fed back from the amplifier to the
transmitter, to reduce power output to this level.
However, much higher drive power to the am-
plifier will cause the protective circuitry to dis-
able the amplifier (to avoid damage to the in-
put circuits). Therefore, when using an exciter
delivering more than 100 Watts of drive power,
the input attenuator should be used. With
Yaesu transceivers, only the FT-1000/D series
should require the use of the attenuator, as
the FT-1000/D is capable of up to 200 Watts
of output power.
ALC Alignment
When this amplifier is used with Yaesu
transceivers such as the FT-1000MP, FT-990,
or FT-920, the ALC system normally will not
require alignment. However, if it appears that
full power is not being achieved due to exces-
sive ALC action, you may align your VL-1000’s
ALC system to that of your transceiver via this
simple procedure:
1. Connect the transceiver to the INPUT 1
jack, and select “INPUT 1” via the front
panel INPUT switch.
2. Set the RF output power to the HIGH
power condition via the front panel LOW
switch.
3. Press the TUNER switch to turn off the an-
tenna tuner (“TUNER” indicator will be
OFF).
4. Press and hold in the INPUT switch for ½
second; this initiates the “ALC Alignment”
mode.
5. Start with the transceiver’s D
RIVE or RF PWR
control fully counter-clockwise, then rotate
the D
RIVE or RF PWR control to the fully
clockwise position while transmitting.
6. If the power output from the amplifier (as
displayed on the AVG meter) does not
reach 1000W because of the effect of the
VL-1000’s ALC voltage at full exciter drive,
keep the transceiver’s D
RIVE or RF PWR
control fully clockwise, then press and hold
in the DISPLAY 2 key until the power out-
put from the amplifier reaches 1000 Watts.
7. If, on the other hand, the ALC voltage from
the VL-1000 does not cause the exciter
drive to be controlled such that the power
output from the amplifier limits at 1000
Watts, do the reverse procedure from that
just described. First, reduce the drive from
the exciter until the VL-1000’s power out-
put is 1000 Watts. Next, press and hold in
the DISPLAY 1 key until the output power
from the amplifier is just reduced from the
1000 Watt level. Now set the transceiver’s
D
RIVE or RF PWR control fully clockwise, and
press the DISPLAY 1 key (to increase ALC
voltage/decrease power output) or DIS-
Operation
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu VL-1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu VL-1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info