478506
12
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
Page 10 VL-1000 Operating Manual
Operation
Preliminary Checks
Before switching on power, recheck all in-
terconnections. Be certain that the ground, RF
input, and ALC connection cables are all se-
cure.
If using a Yaesu FT-980 transceiver for ex-
citation, set the L
IN AMP switch on the rear panel
to the (upper) Position 1. If using an FT-
757GX(II) or FT-767GX, ensure that the L
IN or
L
INEAR switch is depressed (Position 1). Other
Yaesu transceivers do not require special
switch setting on the transceiver prior to com-
mencing amplifier operation
Band Changes
By now, you have noticed that there is no
“B
AND” switch on the VL-1000. Selection of the
frequency band is accomplished in one of two
ways:
If using a Yaesu transceiver with a BAND
DATA control cable, band selection and an-
tenna rematching will occur automatically
whenever you change bands on the trans-
ceiver. Similarly, the antenna last used by
the VL-1000 on each band will be reselected
when that band is recalled on the trans-
ceiver.
If you are using a transceiver without a band
control cable, injecting a carrier from the
exciter for few seconds causes the VL-
1000’s microprocessor to count the input
frequency and automatically set the ampli-
fier up for operation on the appropriate band.
Here are the appropriate procedures:
1. Set the M
ODE switch of the exciter to CW,
and the D
RIVE or RF PWR control of the
exciter so as to provide 50 Watts of less
of drive power to the VL-1000.
2. Press the F SET key on the VL-1000 mo-
mentarily, then press the P
TT switch of
the exciter to activate the transmitter. If
necessary, close your key to allow a car-
rier to be transmitted for a few seconds.
3. The microprocessor of the VL-1000 will
now detect the frequency of the input sig-
nal, and the amplifier will then set itself
to the matching band.
4. When the correct band appears on the
VL-1000 display, release the exciter’s
P
TT switch so as to return to the receive
mode. Preliminary band setup is now
complete.
If you attempt to transmit on an improper
band (for example, at 6.2 MHz), the VL-1000
will automatically be placed in the “THRU”
mode, and no amplification will take place.
Antenna Selection
Pressing the ANT switch repeatedly causes
the VL-1000 to “toggle” between the rear panel
antenna jacks. Just remember to select the
correct antenna when making band changes
during initial operation, and the VL-1000 will
thereafter remember which of ANT 1 through
ANT 4 should be selected when you return to
that band.
When the amplifier is turned off, the default
antenna selection is ANT 1. You may wish to
consider putting a grounding-type coaxial
switch in the coaxial line connected to the ANT
1 jack, so as to shunt static electricity or nearby
lightning pulses to ground.
Fan Operation
The cooling fans for the amplifier and power
supply are both thermostatically controlled. The
thermostats are set to activate well before “dan-
gerous” heat has built up inside the cabinets.
It is quite normal for the fans to cycle on and
off, occasionally, even during receive opera-
tion. The fans also may continue to operate
after the front panel power switch is turned off,
this feature allows the complete dissipation of
heat so as to ensure long life of the compo-
nents.
Important Note
The VL-1000 requires input drive power of
50~60 watts. Please ensure that the trans-
mitter used with this amplifier is capable of
producing at least 60 Watts of drive power
so as to ensure full output from the VL-1000.
When driving the VL-1000 with a transceiver
which includes a built-in antenna tuner,
please turn the transceiver’s antenna tuner
off when using the VL-1000.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu VL-1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu VL-1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info