674740
111
Verklein
Vergroot
Pagina terug
1/154
Pagina verder
Page 109FT-991 OperaTing Manual
pMs
(
proGraMMable MeMorY scanninG
)
To limit scanning (and manual tuning) within a particular frequency range, the Programmable Memory Scanning (PMS)
feature utilizes nine special-purpose memory pairs (“
P-1L
/
P-1U
” through “
P-9L
/
P-9U
”). The PMS feature is especially
useful in helping you to observe any operating sub-band limits, which apply to your Amateur license class.
1. Store the Lower and Upper tuning/scanning limit
frequencies into the memory pair “
P-1L
” and “
P-1U
”,
respectively, or any other “L/U” pair of memories
in the special PMS memory area. See page 98 for
details regarding memory storage.
2. Press the
V/M
button to enter the “Memory” mode.
3. Press the
F(M-LIST)
button, then touch
[
MCH
]
on
the TFT display. The LEDs indicating the Memory
mode will illuminate.
V/M ButtonMULTI Knob
F(M-LIST) Button
4. Rotate the
MULTI
knob to select memory channel
P-1L
” or “
P-1U
”.
5. Press the
F(M-LIST)
button, then touch
[
SQL
]
on
the LCD. Rotate the
MULTI
knob so that the back-
ground noise is just silenced.
6. Turn the Main Tuning Dial knob slightly (to activate
memory tuning). Tuning and scanning are now lim-
ited to the range within the P-1L/P-1U limits until
the
V/M
button is pressed again to return to memory
channel or VFO operation.
7. Press and hold in the microphone
UP
or
DWN
but-
ton for one second, or press the
F(M-LIST)
button
followed by
[
SCAN
]
to start scanning in the speci-
ed direction.
Advice:
If the scanner halts on an incoming signal, the deci-
mal point between the “MHz” and “kHz” digits of
the frequency display will blink.
If the incoming signal disappears, scanning will re-
sume in about ve seconds.
On the SSB/CW and SSB-based Data modes, the
scanner will pause on a received signal, then will
step across the signal very slowly, giving you time to
stop the scan, if you like. However, in these modes
on the VFO, the scanner does not stop.
If the scan has paused on a signal, pressing the mi-
crophone
UP
or
DWN
button, or touching
[
SCAN
]
on the LCD will cause scanning to resume instantly.
If the Main Tuning Dial knob is rotated while scan-
ning is in progress, the scanning will continue up
or down in frequency according to the direction of
the Dial Knob rotation. (in other words, if the dial
is rotated to the left when scanning toward a higher
frequency, the direction of the scan will reverse.)
If the microphone
PTT
button is pressed during
scanning, the scanner will halt at once. Pressing the
PTT
button during scanning will not cause transmis-
sion.
111

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-991 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-991 in de taal/talen: Engels als bijlage per email.

De handleiding is 30,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info