478466
45
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
43FT-7900R OPERATING MANUAL
VFO SCANNING
This mode allows you to scan the entire current operating band.
1. Select the VFO mode by pressing the
[
V/M
(
MW
)]
key, if necessary.
2. Press and hold in the
[
SCAN
(
SEL
)]
key for 1/2 second, then rotate the DIAL knob to
select the bandwidth for the VFO scanner. Available se-
lections are ±1 MHz, ±2 MHz, ±5 MHz, ALL, PMS-X,
and BAND.
ALLALL
ALLALL
ALL: The scanner will sweep all frequencies between 108 - 520 MHz and 700 -999.990
MHz.
PMS-XPMS-X
PMS-XPMS-X
PMS-X: The scanner will sweep frequencies within the currently-selected PMS frequency
pair (
XX
XX
X is PMS memory channel number). See page 47 for details.
BANDBAND
BANDBAND
BAND: The scanner will sweep frequencies only on the current band.
3. Press the
[
SCAN
(
SEL
)]
key momentarily to start scanning.
4. The “
P-XXP-XX
P-XXP-XX
P-XX” indication will appear on the display if you
engage PMS scanning, while the “
P SCP SC
P SCP SC
P SC” indication will
appear on the display when other scanning modes are
engaged.
5. If and when the scanner encounters a signal strong enough to open the squelch, the
scanner will halt temporarily; the decimal point of the frequency display will blink dur-
ing this “Pause” condition.
6. The scanner will then resume according to the Scan-Resume mode selected in the previ-
ous section.
7. To cancel scanning, press the
[
SCAN
(
SEL
)]
key momentarily again (or press the
microphone’s PTT key).
1) When you start scanning, the FT-7900R will be changing frequency in the
upward direction. If you want to change direction of the scan while it is underway,
rotate the DIAL knob one click in the opposite direction (in this case, one click counter-
clockwise). You’ll see the scanner turn around and change frequency downward!
2) Pressing and holding in the microphone’s [UP] or [DWN] key will cause the scanner to
sweep frequencies only on the current band. If you would like the scanner not to be
restricted to the current band, you may change Menu #46 (VFO.BND) to allow the scan-
ner to hop to the low edge of the next-highest band when the VFO frequency reaches the
high end of the current band (or vice- versa). See page 77 for details.
SCANNING
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-7900R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-7900R in de taal/talen: Engels als bijlage per email.

De handleiding is 2,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info