478472
11
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
FT-250R OPERATING MANUAL 7
FREQUENCY NAVIGATION
Press the
[
VFO
(
PRI
)
]
button, if necessary, to select the VFO mode. The FT-250R has
two VFOs, labeled “A” and “B,” either of which can be used for all of the procedures
described in this manual. You can change VFOs with the
[
VFO
(
PRI
)
]
button at any time.
There are several ways to tune the FT-250R: in selectable channel steps or 1 MHz steps
with the
[
(
MHz
)
]
/
[
(
MHz
)
]
keys or DIAL knob, and direct keypad frequency entry.
Use the DIAL knob to tune the displayed VFO frequency at the current channel step rate.
You can also press the
[
(
MHz
)
]
/
[
(
MHz
)
]
keys momentarily to do this.
To change the MHz range of the VFO, you can press the
[
F/L
]
key followed by an
[
(
MHz
)
]
or
[
(
MHz
)
]
key (or turn the DIAL knob). Note the beeps when using the
[
(
MHz
)
]
/
[
(
MHz
)
]
keys when moving up or down. When done, press
[
F/L
]
again, or just wait five
seconds.
You can also enter a frequency directly just by keying in the 10 MHz, 1 MHz and the kHz
digits. Partial entries can be completed using the
[
VFO
(
PRI
)
]
key.
Examples:
To enter 146.5200 MHz, press
To enter 146.5000 MHz, press
CHANGING THE TRANSMITTER POWER LEVEL
You can select between a total of three transmitter power levels on your FT-250R. The
exact power output will vary somewhat, depending on the voltage supplied to the trans-
ceiver. With the standard FNB-83 Battery Pack, the power output levels available are:
HIGHHIGH
HIGHHIGH
HIGH: 5 W
MIDMID
MIDMID
MID: 2 W
LOWLOW
LOWLOW
LOW: 0.5 W
To change the power level:
c
Press the
[
F/L
]
key, then immediately press the
[
3
(
LOW
)
]
key.
d
Now rotate the DIAL knob to select “
LOWLOW
LOWLOW
LOW”, “
MIDMID
MIDMID
MID,” or “
HIGHHIGH
HIGHHIGH
HIGH”.
e
Press the PTT key to save the new setting and exit to normal operation.
CHANGING THE CHANNEL STEPS
To change a frequency step, follow the procedure below:
c
Press the
[
F/L
]
key, then immediately press the
[
0
(
SET
)
]
key to enter the Set mode.
d
Rotate the DIAL to select Menu Item #6 (“
STEPSTEP
STEPSTEP
STEP”).
e
Press the
[
F/L
]
key to enable modification of the current setting.
f
Now rotate the DIAL knob to select 5, 10, 12.5, 15, 20, 25 or 50 kHz steps.
g
Press the PTT key to save the new setting and exit to normal operation.
Basic Operation
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-250R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-250R in de taal/talen: Engels als bijlage per email.

De handleiding is 1,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info