674722
44
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
DR-2X / DR-2XE Operating Manual42
19. Remote Operation with External Controller
Repeater operation may be controlled remotely by connecting an external controller through the
[
CONTROL
I/O
]
connector at the back of the repeater.
The following features are available while in remote operation:
Change the communication mode of repeater transmit and receive
Turn the RX and TX tone signal “ON” or “OFF”
Monitor the discriminator analog or demodulated digital audio during up-link reception
To use the repeater under remote control, set up the repeater as explained below, after it is connected to the
external controller.
Turning remote operation ON/OFF
When the remote operation is “ON”, the repeater operates according to the control instructions received from
the external controller (the instructions are received through Pin 11 to Pin 14 of the
[
CONTROL I/O
]
connector).
When the remote operation is “OFF”, the repeater operates according to the settings determined through the
setup mode.
1 Touch
[
A SETUP
]
.
The setup mode screen will appear.
2 Touch
[
F
]
.
The setup menu will appear.
3 Touch
[
MODE/REMOTE
]
.
The menu list will appear.
4 Touch
[
REMOTE
]
.
The set value will change between
[
OFF
]
and
[
ON
]
each time
[
REMOTE
]
is touched.
z Factory default: OFF
z Remote operation is available only on the CH-A.
z Remote operation is not available in the “HRI + REPEATER MODE”.
M/V
BACK
BACK
>
ON
ON
REMOTE
COMMAND
DISPLAY TIMER
REMOTE/COMMAND/DISP TIMER
5 Touch
[
BACK
]
3 times.
The setting is determined and the display will return to the operation mode screen.
Note that
[
REMOTE
]
at the bottom left of the screen is displayed in red.
You can transmit by the microphone and PTT input of the front panel in all settings except AMS/AMS.
Control from external controller
To control the DR-2X/DR-2XE remotely, optional cables can be used
to connect the repeater to an external controller.
Use the “CONTROL I/O” connector at the back of the repeater to con-
nect with the external controller.
To interface the DR-2X/DR-2XE with an external controller, additional
cables with a 15-pin mini d-sub connector are needed to connect to
the “CONTROL I/O” connector. Your controller may also require rewir-
ing.
Link operation may require four connections: receiver audio, transmit-
ter audio, receiver COR, and transmitter PTT; however, these are not
available on the “CONTROL I/O” connector.
The pin assignment of the “CONTROL I/O” connector is as follows.
Do not use a VGA cable for PC display to connect the external controller
to the repeater.
CONTROL I/O connector
5~1
10~6
15~11
(as viewed from real panel)
44

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu DR-2X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu DR-2X in de taal/talen: Engels als bijlage per email.

De handleiding is 14,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info