738223
39
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
39
b) Turning the measuring device on and off
The digital multimeter is turned on and off via the rotary switch (5). Two beep sounds will sound when turning on the
digital multimeter. All symbols in the LC display (4) will be shown initially for about 2 seconds.
Ensure that the enclosed battery is inserted properly prior to working with the measuring device. A 9 V block
battery is required for voltage supply. It is part of the delivery. Exchange the battery as described in the chapter “11.
Cleaning and Maintenance”.
When the rotary switch (5) is set to “OFF”, the digital multimeter is turned off. Always turn the measuring device off
when it is not in use.
The device is ready for taking measurement within 2 seconds after startup. Restart the device if the error message
“ErrE“ is displayed.
c) Automatic range selection
With the digital multimeter, the automatic range selection (auto range) is active in all measuring functions (except for
temperature and non-contact measuring). This function sets the right measuring range automatically. If applicable,
auto-mode is switched on when switching the rotary switch (5) to any measuring mode.
d) HOLD function
The HOLD button (12) allows you to hold the measuring value on the LC display (4). The symbol “ ” appears
on the LC display (4). This facilitates reading, e.g. for documentation purposes. Another press will switch back
to measuring operation again. Also observe that the HOLD button has not been pushed at the beginning of the
measurement (display with the HOLD button pushed: “H”). If the HOLD function is activated before commencement
of the measurement, no measured value is displayed!
e) Auto shutoff function
The digital multimeter has an auto shutoff function that shuts down the device automatically after 15 minutes of
inactivity (no measurement) to conserve energy. Pressing any key to wake up the device again.
The auto shutoff function is automatically enabled whenever the digital multimeter is switched on. The symbol
shows on the LC display (4).
To disable the auto shutoff function, press and hold the SELECT button (1) while the digital multimeter is “OFF“.
Keep holding down the SELECT button (1) while turning the rotary switch (5) clockwise to turn on the digital
multimeter. The symbol will not show on the LC display (4). The auto shutoff function is disabled. The digital
multimeter stays always on, even if no measurements are taken.
To re-enable the auto shutoff function, switch off the digital multimeter and switch on again without pressing any
other button.
f) Back light function
During any measurement, press and hold the HOLD button (12) for two seconds to turn on the back light of the LC
display (4). Press and hold it for two seconds again to turn the backlight off.
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft VC185 TRMS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft VC185 TRMS in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 10,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info