809762

VTech VM5261 Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Parent unit main menu icons
Alert Tone
You can set the parent unit to beep
when
• the parent unit operates in low
battery condition;
• the link between the parent unit
and the baby unit is lost; or
Language
You can select a language (English,
French or Spanish) to be used in all
screen displays.
LCD
You can change the brightness of
the parent unit screen, or turn on
the Dim Mode to save power.
Rename
You can choose a specific name for
the baby unit from a pre-defined
name list.
VOX Sensitivity
With this feature, you can choose
to hear sounds from the baby unit
all the time, or to hear sounds that
exceed a certain level. You can
use the parent unit to adjust the
microphone sensitivity of your baby
unit. The higher the sensitivity level,
the more sensitive the baby unit is in
detecting sounds for transmitting to
the parent unit.
Sound-activated Screen
When the baby unit being viewed
detects no sound, the parent unit
screen stays off to save power.
Once a sound is detected, the
parent unit screen turns on
automatically. It will then turn off
again after 50 seconds of no sound
detection.
Temperature
You can turn on the temperature
alert tone so that the parent
unit beeps whenever the room
temperature detected by the baby
unit falls outside of the desired
temperature range.
You can choose to display the
temperature in Fahrenheit (oF) or
Celsius (oC), or set the maximum/
minimum temperature limit for alerts.
Lullaby on CAM
You can choose a lullaby or
soothing sound to comfort your
baby.
Volume on CAM
You can adjust the volume of baby
unit which determines the lullaby
volume and talkback volume
transmitted from parent unit.
Vibration
You can turn on the vibration alert
so that the parent unit vibrates
when it receives Low battery tone,
No link alert or Temperature alert
tone after turning on the respective
alert tones.
Parent unit warning icons and
messages
No link to CAM
# *
The selected baby unit is
out of range or is turned
off.
Battery low at
Parent Unit
The battery level of the
parent unit is very low and
needs to be recharged.
Battery empty.
Powering off ... The battery is empty and
needs to be recharged.
Temperature
too high at CAM #
or
Temperature
too low at CAM #
The temperature detected
by the baby unit is higher/
lower than the desired
temperature alert range.
The parent unit is
searching for the baby
unit.
Auto Timer of
lullaby is reset The auto timer for playing
lullaby is reset.
* # represents the baby unit number.
Using the baby monitor
Power on or off the baby unit
• Slide the ON/OFF switch to the left to turn on
the baby unit. The ON/OFF LED light turns
on.
• Slide the ON/OFF switch to the right to turn
off the baby unit. The ON/OFF LED light turns
off.
Power on or off the parent unit
• Press and hold POWER to turn on the parent
unit. The screen turns on.
• Press and hold POWER to turn off the parent
unit. The screen turns off.
Turn on or off the parent unit screen
You can turn on or off the parent unit screen
without powering off the parent unit. You can
still hear sound from the baby unit.
• Press and hold LCD ON/OFF on the parent
unit to turn off the screen.
• Press any key on the parent unit to turn on
the screen again.
Adjust the speaker volume
For parent unit:
• Press / on the parent unit at any
time when viewing images.
• When the parent unit speaker volume is set to zero,
appears on the screen and the light turns on.
For baby unit:
The baby unit speaker volume can be adjusted
in the parent unit. The baby unit speaker
volume determines the lullaby volume and
talkback volume transmitted from parent unit.
Level 1 is the softest while Level 5 is the loudest.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Volume on CAM,
then press SELECT.
3. Press or to choose the desired volume
level, then press SELECT to confirm your
selection.
Adjust LCD brightness
You can change the brightness of the parent
unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press MENU when the parent unit is inactive.
2. Press or to choose LCD, then press
SELECT.
3. Press SELECT again to choose Brightness.
4. Press or to choose the desired level of
brightness, then press SELECT to confirm your
selection.
Turn on or off the dim mode
The dim mode is preset to on to help you save
the parent unit power. Your parent unit display
will dim automatically after 10 minutes of
inactivity, in which there is neither key pressed
nor alert received from the baby unit.
1. Press MENU when the parent unit is inactive.
2. Press or to choose LCD, then press
SELECT.
3. Press or to choose Dim Mode, then
press SELECT.
4. Press or to choose On or Off, then press
SELECT to confirm your selection.
• While the screen is dimmed, any keypress or
alert message will trigger the screen to return to
the preset brightness level. After 10 minutes of
inactivity, it will be dimmed again.
Pan, tilt, zoom
You can remotely pan and tilt your baby unit
camera or zoom in while viewing images from
the baby unit.
• Press and hold , , or to tilt the baby
unit camera downward, upward, leftward or
rightward.
• Press to zoom in. Press again to zoom out.
• Press and hold , , or to move
the zoomed image downward, upward,
leftward or rightward.
Talk
You can use the TALK function of the parent unit
to comfort your baby
1. Press and hold TALK on the parent unit. The
TALK light turns on.
2. Speak towards the microphone on the parent
unit. Your voice is broadcast to the baby unit.
3. Release TALK to stop the broadcast. The TALK
light goes off. The speaker is then turned on
for around 20 seconds, so you can hear your
baby.
NOTE
S
• The parent unit speaker is muted during voice
broadcast. Sound transmission from the baby unit
resumes after TALK is released.
• After around 20 seconds of sound re-transmission,
the speaker returns to mute if you had set it to mute
before pressing TALK.
Lullaby
The baby monitor has five lullabies and four
soothing sounds for you to comfort your baby.
You can play the lullabies or soothing sounds on
the baby unit using the parent unit.
To play lullaby using the parent unit:
1. Press MENU when the parent unit is inactive.
2. Press or to choose Lullaby on CAM, then
press SELECT.
3. Press or to choose Play Melodies, then
press SELECT.
4. Press or to choose a lullaby, or choose
Play All, then press SELECT.
• If Play All is selected, the lullabies will
be played one after the other, until all
lullabies are played.
5. When the desired lullaby is selected, press
or to choose Play, then press SELECT.
To play soothing sound using the parent unit:
1. Press MENU when the parent unit is inactive.
2. Press or to choose Lullaby on CAM, then
press SELECT.
3. Press or to choose Play Soothing
Sounds, then press SELECT.
4. Press or to choose a soothing sound,
then press SELECT.
5. Press or to choose Play, then press
SELECT.
NOTES
• The lullaby playback on the baby unit will be
paused when receiving talkback from the parent
unit.
To stop playing lullaby or soothing sound:
1. Press MENU when the parent unit is inactive.
2. Press or to choose Lullaby on CAM, then
press SELECT.
3. Press or to choose Stop, then press
SELECT.
To set auto timer for lullaby:
While the baby unit is playing lullaby or
soothing sound, the auto timer feature helps you
automatically stop the lullaby or soothing sound
after playing for 15/30/45/60 minutes. You can
set auto timer for lullaby with the parent unit.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Lullaby on CAM, then
press SELECT.
3. Press or to choose Auto Timer, then
press SELECT.
4. Press or to choose the desired lullabies
duration, then press SELECT.
After 15/30/45/60 minutes, the lullaby or
soothing sound will stop automatically.
Adjust the sound sensitivity of the
baby unit
You can choose to hear sounds from the baby
unit all the time, or to hear sounds that exceed
a certain level. You can use the parent unit to
adjust the microphone sensitivity of your baby
unit from Lowest to Highest. The higher the
sensitivity level, the more sensitive the baby unit
is in detecting sounds for transmitting to the
parent unit. The VOX sound sensitivity level is
preset to Highest.
Sensitivity
Level
Description
Highest
Low
sensitivity
High
sensitivity
Highest VOX sensitivity
level
The parent unit speaker is
constantly on, and you will
hear all sounds (including
background noises) from
your baby’s room.
High
High VOX sensitivity level
The parent unit speaker turns
on for soft babbling and
louder sounds from your
baby. It remains quiet when
your baby sleeps soundly.
Medium
Medium VOX sensitivity
level
The parent unit speaker
turns on for loud babbling
and louder sounds from
your baby. It remains quiet
when your baby makes soft
sounds.
Low
Low VOX sensitivity level
The parent unit speaker
turns on for crying and
louder sounds from your
baby. It remains quiet
when your baby makes soft
sounds.
Lowest
Lowest VOX sensitivity level
The parent unit speaker
turns on for loud crying or
screeching sounds from
your baby. It remains quiet
when your baby makes soft
sounds.
1. Press MENU when the parent unit is inactive.
2. Press or to choose VOX Sensitivity, then
press SELECT.
3. Press or to choose the desired sensitivity
level, then press SELECT to confirm your
selection.
TIP
• You can adjust the baby unit placement to improve
the sound detection.
Turn on or off the sound activation
When sound activation is on, as long as no
sound is detected within 50 seconds, the parent
unit screen will turn off automatically to save
power.
When your baby unit detects a sound, which
exceeds the selected sensitivity level, the sound
activation triggers the parent unit screen to turn
on automatically. When no sound is detected
within 50 seconds, the screen will be off again.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Sound-activated
Screen, then press SELECT .
3. Press or to choose On or Off, then press
SELECT to confirm your selection.
NOTES
• If the sound sensitivity is set to Highest, or lullaby
is playing, the parent unit screen may remain on
continuously even though sound activation is on.
This depends on whether the baby unit detects any
sounds.
Set alert tone
Low battery tone
You can set the parent unit to beep when the
parent unit operates in low battery condition.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Alert Tone, then
press SELECT.
3. Press SELECT again to choose
Low Battery Tone.
4. Press or to choose On or Off, then press
SELECT to confirm your selection.
No link alert
You can set the parent unit to beep when the
link between the parent unit and the baby unit
is lost.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Alert Tone, then
press SELECT.
3. Press or to choose No Link Alert, then
press SELECT.
4. Press or to choose On or Off, then press
SELECT to confirm your selection.
Monitor the temperature
Your baby unit monitors the temperature of your
baby’s room with its built-in temperature sensor.
If the detected temperature is outside of the
preset temperature range, the parent unit will
display alert message.
Set temperature range
You can set the desired room temperature alert
range. The minimum temperature can be set
between 11 oC (52 oF) and 20 oC (69 oF).
The maximum temperature can be set between
21 oC (70 oF) and 30 oC (86 oF).
1. Press MENU when the parent unit is inactive.
2. Press or to choose Temperature, then
press SELECT.
3. Press or to choose Minimum or
Maximum, then press SELECT.
4. Press or to choose the desired minimum
or maximum temperature, then press SELECT
to confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so
that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Temperature, then
press SELECT.
3. Press or to choose Alert Tone, then
press SELECT.
4. Press or to choose On or Off, then press
SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in
Fahrenheit (oF) or Celsius (oC).
1. Press MENU when the parent unit is inactive.
2. Press or to choose Temperature, then
press SELECT.
3. Press or to choose Format, then press
SELECT.
4. Press or to choose oF or oC, then press
SELECT to confirm your selection.
Turn on or off the vibration
You can turn on the vibration feature so that the
parent unit vibrates when it receives any of No link
alert, Sound alert in split-view or Temperature
alert tone after turning on the respective alert
tones.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Vibration, then press
SELECT .
3. Press or to choose On or Off.
4. Press SELECT to confirm your selection.
NOTES
• If the vibration feature is turned on, the parent unit
may vibrate as it receives sound broadcast from the
baby unit.
Set the language
You can select a language (English, French or
Spanish) to be used in all screen displays.
1. Press MENU when the parent unit is inactive.
2. Press or to choose Language, then press
SELECT.
3. Press or to choose English, Français or
Español, then press SELECT to confirm your
selection.
Rename the baby unit
You can rename each baby unit. Once the baby
unit is renamed, its new name together with the
baby unit number will appear in the sub-menu
of below options:
• VOX Sensitivity • Rename
• Temperature
1. Press MENU when the parent unit is inactive.
2. Press or to choose Rename, then press
SELECT.
3. Press or to choose the desired baby unit,
then press SELECT.
4. Press or to choose the desired name for
the baby unit, then press SELECT to confirm
your selection.
Night vision
The baby unit has infrared LEDs that allow you
to see your baby clearly at night or in a dark
room. When the baby unit being viewed
detects low light levels, the infrared LEDs are
switched on automatically. The images from this
baby unit are in black and white, and
appears on screen.
NOTE
S
• It is normal if you see a short white glare on your
parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in
black and white. This is normal.
TIP
• Depending on the surroundings and other
interfering factors, like lightings, objects, colours
and backgrounds, the display resolution may vary.
Adjust the baby unit’s angle or place the baby unit
at a higher level to prevent glare and blurry display.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit
in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and
the adaptors in a cool and dry place.
Frequently asked questions
Below are the questions most frequently asked about the
baby monitor.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed)
for common cure:
1. Disconnect the power to the baby
unit and the parent unit.
2. Remove the batteries in the parent
unit. Then, install the batteries
again.
3. Wait a few seconds before
connecting power back to the
baby unit and the parent unit.
4. Turn on the baby unit and the
parent unit.
5. Wait for the parent unit to
synchronize with the baby unit.
Allow up to one minute for this to
take place.
Why don’t
the power-on
light of the
baby unit and
parent unit
go on when I
switch on the
units?
Perhaps the parent unit is not
connected to the power. Insert the
appliance plug into the parent unit and
put the adaptor in a wall socket. Then,
press and hold POWER to switch
on the parent unit and to establish
connection with the baby unit.
Perhaps the baby unit is not
connected to the power. Insert the
appliance plug into the baby unit
and put the adaptor in a wall socket.
Then, slide the ON/OFF switch to
ON to switch on the baby unit and
to establish connection with the
parent unit.
Why doesn’t
my parent
unit charge
while
connected to
AC power?
Make sure the power is not
controlled by a wall switch. If it
does, make sure the controlled
switch is on.
Make sure the battery is installed.
You may have used the battery for a
long time. Replace a new battery.
Why is my
screen in
black and
white?
The screen is in black and white
during night-time or in a dark room
when the night vision feature is
activated. This is normal.
Why do I get
glare or blurry
display on my
screen when
viewing my
baby at night?
During night-time or in a dark
room, the surroundings and other
interfering factors, like lightings,
objects, colours and backgrounds
may affect the image quality on
your parent unit screen. Adjust the
baby unit’s angle or place the baby
unit at a higher level to prevent
glare and blurry display.
Why does the
baby monitor
produce a
high-pitched
noise?
The parent unit and baby unit may
be too close to each other.
• Move the parent unit away from
the baby unit until the noise stops;
OR
• Turn down the volume of your
parent unit.
Why does the
parent unit
beep?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than 3 feet or
1 metre).
If the parent unit is powered by the
provided battery, it may not have
enough charge for the parent unit to
perform normally. Charge the battery
in the parent unit for up to 3 hours.
The temperature of your baby’s
room may be too high or too low.
Why does
the parent
unit react too
quickly to
other sounds?
The baby unit also picks up other
sounds than those of your baby.
Adjust the sensitivity level to a
lower level or lower the parent unit
speaker volume.
Why don’t I
hear a sound/
Why can’t I
hear my baby
cry?
The parent unit speaker volume may
be too low or off. Press to
increase the volume.
You may have set a low sound
sensitivity level. See Adjust the
sound sensitivity of the baby unit to
set to a higher level.
Why can’t I
establish a
connection?
Why is the
connection
lost every
now and
then? Why are
there sound
interruptions?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than 3 feet or
1 metre).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. This product is intended as an aid. It is not a
substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a medical
monitor.
5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in a
wet basement or shower.
6. CAUTION: Use only the batteries indicated in this
manual. There may be a risk of explosion if a wrong
type of battery is used for the parent unit. Use only
the supplied rechargeable battery or replacement
battery pack for the parent unit. Do not dispose of
batteries in a fire. They may explode.
7. Use only the adaptors included with this product.
Incorrect adaptor polarity or voltage can seriously
damage the product.
Baby unit power adaptor: Output: 5V DC 800mA
Parent unit power adaptor: Output: 5V DC 1A
8. The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
tips are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
10. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
11. Unplug the power cords before replacing batteries.
12. Do not cut off the power adaptors to replace
them with other plugs, as this causes a hazardous
situation.
13. Do not allow anything to rest on the power cords.
Do not install this product where the cords may be
walked on or crimped.
14. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home, consult your dealer or local
power company.
15. Do not overload wall outlets or use an extension
cord.
16. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
17. This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or
heat register.
18. Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the product other than
specified access doors may expose you to
dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
20. You should test the sound reception every
time you turn on the units or move one of the
components.
21. Periodically examine all components for damage.
22. Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
23. Children should be supervised to ensure that they
do not play with the product.
24. The product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
25. WARNING! Strangulation Hazard! Keep adaptor
cord at least 3 feet (1 metre) away from the child
at all times.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature
between 0oC and 40oC.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to
a heating source.
3. Batteries should not be exposed to excessive heat
such as bright sunshine or fire.
4. Make sure the baby unit and the adaptor cord
are always out of reach of the baby, at least 3
feet (1 metre) away from the baby or cot, to
avoid a possible strangulation hazard.
5. Never place the baby unit inside the baby’s cot or
playpen. Never cover the baby unit or parent unit
with anything such as a towel or a blanket.
6. Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away from
these electronic devices as possible: wireless
routers, radios, cellular telephones, intercoms,
room monitors, televisions, personal computers,
kitchen appliances and cordless telephones.
Customer service and product
warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
Please call our Consumer Services Department on
01235 546810 (from UK) or +44 1235 546810
(outside UK) and a service representative will be
happy to help you.
Declaration of Conformity
This product is intended for use within Europe.
This equipment complies with the essential
requirements to EU Directive 2014/53/EU on radio
systems and telecommunication equipment.
Vtech Telecommunications Ltd. hereby declares that
this Video Monitor VM5261 is in compliance with the
essential requirements and other relevant provisions of
Directive 2014/53/EU.
The Declaration of Conformity for the VM5261 is
available from http://www.vtech.com/rtte-directive.
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 5” Colour LCD
(WQVGA 480x272 pixel)
Nominal
effective
range
Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Parent unit: 3.7V Li-polymer battery
Baby unit power adaptor: Output:
5V DC @ 800mA
Parent unit power adaptor: Output:
5V DC @ 1A
Disposal of batteries and
product
The crossed-out wheelie bin symbols
on products and batteries, or on their
respective packaging, indicates they
must not be disposed of in domestic
waste as they contain substances that
can be damaging to the environment
and human health.
The chemical symbols Hg, Cd or
Pb, where marked, indicate that
the battery contains more than the
specified value of mercury (Hg),
cadmium (Cd) or lead (Pn) set out in
Battery Directive (2006/66/EC).
The solid bar indicates that the product
was placed on the market after 13th
August, 2005.
Help protect the environment by
disposing of your product or batteries
responsibly.
Technical specifications
This warranty is valid for the UK and Eire only. For products purchased outside
the UK and Eire, please contact your local distributor or place of purchase.
PRODUCT WARRANTY
PRODUCT REGISTRATION
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR Thank you for choosing this quality product from VTech.
We hope it will bring many hours of entertainment,
imaginative play and learning.
1. The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2. The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3. VTech Electronics Europe plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4. If the product covered by this warranty is damaged due to misuse, modification or
unauthorised repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5. This warranty is personal to the original purchaser and is not transferable.
6. Breakages to the LCD screen are not covered by the warranty.
7. Returns to VTech Electronics Europe plc should include a cheque or postal order for
£1.50 towards the cost of return postage and packaging.
8. Products returned to VTech Electronics Europe plc, should be addressed as follows and
packed carefully to avoid damage in transit (Please do not include batteries or adaptor).
Please include details of the fault together with your name and address.
9. To keep an online record of your warranty, please register your product online at www.
vtech.co.uk/warranty
Vtech Electronics EU PLC, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane, West
Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions, find
out about news and events, seek expert advice for parents and
let your kids play fun learning games and activities.
Specifications are subject to change without notice.
© 2019 VTech Telecommunications Ltd.
All rights reserved. 10/19. VM5261_UK_CIB_V1.0
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech VM5261 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech VM5261 in de taal/talen: Engels als bijlage per email.

De handleiding is 4.15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info