809762

VTech VM5261 Handleiding

1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Congratulations
on purchasing your new VTech product. Before
using this product, please read Important safety
instructions.
This manual has all the feature operations and
troubleshooting necessary to install and operate
your new VTech product. Please review this
manual thoroughly to ensure proper installation
and operation of this innovative and feature rich
VTech product.
What’s in the box
Install the battery
The parent unit runs on rechargeable battery or
AC power. To continuously monitor your baby,
make sure you use both battery and AC power
at the same time. With the battery alone, the
parent unit can cordlessly run for a short time
only.
NOTE
S
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
Install the battery as shown below.
NOTES
• Press down on the battery compartment cover to
pull it out.
THIS SIDE UP
NOTES
• Make sure the label THIS SIDE UP is facing up while
inserting the battery.
Replace the battery
To replace the battery, pull out the battery
compartment cover, and then lift up the battery.
Follow the steps above to install the new
battery.
Connect and charge the
battery
NOTE
S
• Use only the power adaptors supplied with this
product.
• Make sure the electrical outlets are not controlled by
wall switches.
• The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
tips are not designed to hold the plug in place if
they are plugged into a ceiling, under-the-table or
cabinet outlet.
• Make sure the parent unit, the baby unit and the
power adaptor cords are out of reach of children.
Connect the baby monitor
Charge the parent unit battery
When you have connected the parent unit
and installed its battery for the first time or
after power outage, the parent unit powers on
automatically. The battery icon indicates the
battery status (see the following table).
NOTE
S
• The parent unit battery is fully charged after
3 hours of continuous charging.
• It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
• The standby time varies depending on the volume
level you set, your actual use and the age of the
battery.
Battery
indicators
Battery status Action
The battery
icon is off and
displays.
No battery
is installed
but operates
using AC
power, or the
battery has
been installed
incorrectly.
Install the
parent unit
battery.
Charge
without
interruption
(at least 30
minutes).
The screen
displays
Battery low
at Parent
Unit and
. The light
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about 30
minutes).
The battery
icon
becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
Mount the baby monitor (optional)
Before use
NOTES
• This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You may test the baby monitor before initial use,
and at regular times thereafter.
CAUTION
• For hearing protection, make sure the parent
unit is more than 3 feet (1 metre) away from
the baby unit. If you hear any high-pitched
noise, move the parent unit further until the
noise stops. You can also press VOL/- on the
parent unit to lower or mute the noise.
1. Make sure your baby unit and parent unit are
on.
2. The parent unit displays images from the
baby unit.
• Speak towards the microphone of the
baby unit. You will hear the sound at the
parent unit.
NOTES
• When the parent unit displays and then
No link to CAM # (# represents the baby unit
number), and the LINK LED light flashes, move the
parent unit closer to the baby unit (observe the
minimum distance of 3 feet/ 1 metre). You can also
check if the baby monitor is connected to a live
power socket and switched on.
TIP
• Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby unit.
Positioning the baby monitor
CAUTION
• Keep the baby unit out of reach of your baby.
Never place or mount the baby unit inside the
baby’s cot or playpen.
NOTE
• To avoid interference from other electronic devices,
place your baby monitor far away from devices such
as wireless routers, microwaves, cell phones and
computers.
1. Place the baby unit more than 3 feet
(1 metre) away from your baby.
2. Place the parent unit more than 3 feet
(1 metre) away from the baby unit.
>
< 3ft (1m)
3ft (1m)
63ē
63ē
CAUTION
• The default volume of your parent unit is level
4, and the maximum volume is level 7. If you
experience high-pitched screeching noise from
your baby monitor while positioning:
- Make sure your baby unit and parent unit are
more than 3 feet (1 metre) apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up
to 1,000 feet (300 metres) outdoors or 160 feet
(50 metres) indoors. The actual operating range
may vary depending on the environmental
conditions and other interferences such as walls,
doors and other obstructions.
Install the lens (optional)
The wide-angle lens provided allows you to
view more of your baby’s room from the parent
unit screen. Install the wide-angle lens onto the
baby unit camera as shown below.
Remove the lens
• When the lens is not in use, cover both sides of
the lens with the lens covers provided to avoid
scratches.
Overview
Baby unit overview
1Antenna
2Temperature sensor
3ON/OFF switch
• Slide to turn on or off the baby unit.
4ON/OFF LED light
• On when the baby unit is turned on.
• Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
5Light sensor
6Camera
7Infrared LEDs
8Microphone
9Speaker
10 Power jack
11 Threaded socket
12 PAIR
• Your baby unit and parent unit
provided are already paired.
Parent unit overview
1LED lights
• Indicate the different statuses of the
parent unit. For details, refer to
Parent unit lights.
2LCD display
3
• Press to increase the parent unit
speaker volume.
4
• Press to decrease the parent unit
speaker volume.
5 Zoom
• Press to zoom in or out.
6VIEW
• Press to view the image of the baby
unit.
LCD ON/OFF
• Press and hold to turn off the parent
unit screen.
7Microphone
8POWER
• Press and hold to power on.
• Press and hold again to power off.
9TALK
• Press and hold to talk to the baby unit.
10
• While in a menu, press to return to
the main menu or idle screen.
• Press and hold to move the baby unit
camera leftward.
• While viewing zoomed image,
press and hold to move the zoomed
image leftward.
11
• While in a menu, press to scroll up.
• Press and hold to move the baby unit
camera upward.
• While viewing zoomed image,
press and hold to move the zoomed
image upward.
12
• While in a menu, press to choose an
item.
• Press and hold to move the baby unit
camera rightward.
• While viewing zoomed image,
press and hold to move the zoomed
image rightward.
13 MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
14
• While in a menu, press to scroll down.
• Press and hold to move the baby unit
camera downward.
• While viewing zoomed image,
press and hold to move the zoomed
image downward.
15 Antenna
16 Stand
17 Speaker
18 Power jack
19 Battery compartment cover
Parent unit lights
LINK • On when the parent unit is linked to
the baby unit.
• Flashes when the link to the baby
unit is lost.
• On when the parent unit is
connected to AC power, or the
battery is charging.
• Flashes when the parent unit
battery is low and needs charging.
• Off when the parent unit is
disconnected from AC power.
It turns on:
• When the speaker volume of the
parent unit is turned off; or
• When the parent unit is talking to
the baby unit.
TALK • On when the parent unit is talking
to the baby unit.
Parent unit status icons
Connection status
• displays when strong signal
strength is detected between the
baby unit and the parent unit.
• or displays when moderate
or low signal strength is detected
between the baby unit and the parent
unit.
• displays when the link between the
baby unit and the parent unit is lost.
Lullaby
• Displays when the baby unit being
viewed is playing lullabies or
soothing sounds.
Current view status
Night vision
• Displays when the night vision
feature is on.
Zoom
• Displays when the current image on
the parent unit has zoomed in.
Temperature alert tone
• Displays when the temperature
alert tone is on.
oF or
oC
Real-time temperature
• Displays the real-time temperature
detected by the baby unit in
Fahrenheit (oF) or Celsius (oC)
(e.g. 57 oF or 14 oC).
Volume off
• Displays when the parent unit
speaker volume is set to off.
9-level sound indicator
• (1 to 3 bars) indicates low sound
level detected by the baby unit.
• (4 to 6 bars) indicates moderate
sound level detected by the baby
unit.
• (7 to 9 bars) indicates high
sound level detected by the baby
unit (e.g. baby crying loudly).
Speaker volume
• Displays the parent unit speaker
volume level while adjusting.
Battery status
• animates
when the battery is charging.
• displays solid when the battery
is fully charged.
• displays when the battery is low
and needs charging.
AC power without battery
• Displays when the parent unit is
connected to AC power without the
battery.
User’s manual
VM5261
Full Colour Video Monitor
with Wide-angle Lens
1
2
3
4
5
6
7
8
10
11
12
1
2
3
4
5
6
8
9
9
10
11
12
13
7
11
12
If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than a stud,
insert the wall anchors into the holes. Tap gently on
the ends with a hammer until the wall anchors are flush
with the wall.
Place the wall mount bracket on a wall and then use a
pencil to mark the top and the bottom holes as shown.
Remove the wall mount bracket and drill two holes in the
wall (7/32 inch drill bit).
NOTES
• Check for reception strength and camera angle before drilling the
holes.
Align the wall mount bracket and screws with the holes in
the wall as shown. Tighten the screw in the middle hole
first, so that the wall mount bracket position is fixed. You
can tighten the other screw in the top hole.
Place the baby unit on the wall mount bracket. Tighten
the screw into the threaded socket at the bottom to
secure the baby unit.
Insert the screws into the holes and tighten the screws
until only 1/4 inch of the screws are exposed.
The default angle of the wall mount bracket is 90 degrees. You can maximize your baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the
joint and secure the angle.
Place the baby unit on the wall mount bracket. Tighten
the screw into the threaded socket at the bottom to
secure the baby unit. Align the holes on the wall mount
bracket with the screws on the wall, and slide the wall
mount bracket down until it locks into place.
OR
Go to www.vtech.co.uk
to register your product for
warranty support.
Important
• To maximize the life of the parent unit’s
battery, we recommend you fully charge
the battery as instructed, before using the
video monitor for the first time.
> 3ft (1m)
63ē
> 3ft (1m)
63ē
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech VM5261 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech VM5261 in de taal/talen: Engels als bijlage per email.

De handleiding is 4.15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info