652329
14
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
14
L
Ø A
2.7 - BURNER
2.7.2 - CHOICE OF THE BURNER
The correct choise and the adjustment of the
burner are foundamental for the best operation
of the boilerand then they shall be accurate
and not underevaluated.
The burner will be selected by verifying that
its working diagram (fuel flow rate - pressure
in the furnace) is compatible with the same
features declared for the boiler.
Remember that the smoke side resistance,
i.e. the counterpressure in the furnace, are
referred to "0" draught at the chimney base.
It is also convenient that the burner blast tube
have its length not shorter than that shown
in table 17 and that the flame have a shape
suitable to the characteristics of the ELLPREX
furnace.
In fact to better exploit all the heating surface
of the reversed flame furnace it is necessary
to use burners capable to guarantee a long
and narrow flame at all operating conditions
or also at minimum input in case of two stage
or modulating burners.
Too short flames can cause a localized
overheating of the front part of the furnace,
and the combustion products, not sufficiently
BOILER MODEL
øA
mm
L
mm
fig. 17
ELLPREX 2200 - 2650
380 350
ELLPREX 1570 - 1850
320 320
ELLPREX 1100 - 1320
320 300
ELLPREX 760 - 970
270 270
ELLPREX 290 - 630
210 250
ELLPREX 170 - 240
180 250
2.7.1 - CONFORMITY OF THE BURNER
All the burners equipping the ELLPREX boilers
must be CE certificated and must conform
cooled down, entering the smoke pipes at a
too high temperature, can cause important
damages to the boiler.
The burner manufacturing companies are
able to supply the flame dimensions
developped by their burners.
More informations are given in the paragraph
"Commissioning".
to the following directives and standards:
- Gas Appliances Directive (90/396/CEE);
- EMC Directive (89/336/CEE).
- EN 267 - Automizing oil burners of
monobloc type - Testing -
- EN 676 - Automatic forced draught burners
for gaseous fuels.
ELLPREX 3000 - 3500
380 400
BURNER BLAST TUBE MIN. LENGTH
2.7.3 - BURNER INSTALLATION
Before fitting the burner it is necessary to
verify the position of the turbulators inside
the smoke pipes: each pipe must have its
turbulator and this one has to be positioned
as indicated in the table on page 28.
When mounting the burner to the boiler front
door, check for soundness around the burner
flange and its gasket.
Each boiler is supplied with a length of ceramic
fibre rope (cross section 25x25 mm).
This rope has to be put around the burner
tube to completely seal the tube and the
hole in the door insulation.
Be careful not to leave fissures between the
burner tube and the hole in the door.
In case a cone, having a diameter langer than
the burner tube, the cone is to be removed
before fitting the burner and refitted later on.
After the burner has been fitted, check that
the flexible hoses for the oil and the electrical
cables are long enough to allow the 90°
opening of the boiler door.
For gas burners the use of flexible pipes for
the gas is not allowed; so the final part of the
gas feeding line to the burner must have the
possibility to be removed, via a threaded or
flanged connection.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Unical Ellprex bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Unical Ellprex in de taal/talen: Engels als bijlage per email.

De handleiding is 0,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info