581328
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
7
8
Press the tabs to open
the thermostat.
21
22
Back-Cover
Wall
Through Hole
Wires
Wall
Wi res
Back-Cover
Te r mina l s
Figure 1
LEVEL
Mark the locations
with a pencil
Back-Cover
+
+
++
++
++
++
++
++
++
++
++
++
++
Repeat the procedures for weekday program 3 and 4, and similarly for Saturady programs (P1 - P4)
and Sunday programs (P1 - P4)
After complete setting of all 12 programs,
if you have the THM302M, press PROG to return to normal display (SET PROGRAM symbol
will disappear).
If you have the THM303M, press PROG once will take you to humidity setting (seeing Humidifier
Control) or press PROG twice to return to normal display.
Note:
The PROG key can also be used
anytime to review all the set programs.
To terminate the programming
sequence at anytime, press
DISPLAY key.
Tip:
Press and hold the AHEAD/BACK or
UP/DOWN key to change the numbers
quickly.
Cooling Programs
Slide the system switch to the COOL position and repeat the programming as you would for the Heating Programs.
Note: The Humidifier Control (THM303M) only functions in HEAT mode.
Temporary Override
To change the temperature temporarily, press UP or DOWN to set the desired temperature. The OVERRIDE
symbol will appear. The thermostat will return to the regular program at the next scheduled program time.
Note: The thermostat has an automatic delay function to protect the heating and cooling systems from
undesired on/off sequences. Sometimes there will be a delay of several minutes before the thermostat
will activate the system.
Hold
This feature is to hold the thermostat at a constant temperature and disable all set programs until released.
Press HOLD once and use UP or DOWN button to set the desired hold temperature. HOLD symbol will
appear to indicate that the Hold function is active.
To cancel Hold function, press HOLD again. The HOLD symbol will disappear and the thermostat will
return to the programmed temperature.
Mounting The Thermostat Back-Cover
The back-cover should be mounted horizontally with
the terminals on the left side.
Thread the existing wiring through the big center hole
from the back and set the back-cover horizontally on
the wall.
Select two appropriate mounting holes and mark the
locations with a pencil. If necessary, use a level to make
sure the thermostat is leveled.
Remove the back-cover from the wall and drill two 3/16
inch holes in the marked screw positions. Insert the
wall-anchors into the holes completely. If necessary,
use a hammer to tap-in lightly.
Mount the back-cover with the two screws to the wall.
Make sure the metal terminals are on the left side.
Connecting The Wires To The Terminals
Connect the previously labeled wires to the corresponding
terminals, matching the designations. Use a screwdriver to
securely fasten the wires onto the terminals. Make sure the
wires do not short-circuit with other terminals.
Depending on your heating/cooling equipment, you may
need to connect 2 to 9 wires to the thermostat.
If you have two ‘R’ wires, then connect each wire to its
corresponding terminal and remove the JUMPER between
the RC and RH terminals.
If you are unsure of the connections, or for new installation,
you may refer to the wiring diagrams on the next page:
1
2
3
4
5
6
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw UPM THM302M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van UPM THM302M in de taal/talen: Engels als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van UPM THM302M

UPM THM302M Gebruiksaanwijzing - Français - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info