581328
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Program
Weekday
AM/PM mode
Time
Relative Humidity
3
4
HEAT/COOL CONTROL
LCD DISPLAY
DISPLAY
UP
DOWN
FAN CONTROL
SET CLOCK
PROGRAM
AHEAD
RESET
HOLD
BACK
USAGE
Function Key Descriptions
LCD Display
26
Set Time and Day
Press SET CLOCK to start time setting. The time and SET symbol will flash.
Use AHEAD or BACK to set the current time.
Press SET CLOCK again. The day and SET symbol will flash.
Use AHEAD or BACK to set the current day.
Press SET CLOCK again to exit.
INSTALLING THE BATTERY
SELECT C / F display
Install the two AA size batteries (included) to the thermostat following the polarity as marked. The LCD
display will show the room temperature flashing in Celsius. Press UP or DOWN to change the
temperature display between C and F.
Press SET CLOCK, and the thermostat would go to clock setting / normal display.
Note: This is a one-time process. The temperature unit of the thermostat CANNOT be changed
afterwards unless you reset the thermostat.
Attaching The Thermostat To The Back-Cover
Attach the thermostat body to the back-cover that is already installed on the wall by snapping the
hinges together. Flip up the thermostat and it will snap close.
Congratulations! You have completed the installation of the thermostat. Please refer to the operations
manual for programming and operating instructions.
°°
°°
Set / Program
Temperature
Curent Temperature
25
+
+
-
-
HE
HG
+
_
Setting The Fan Operation Jumper
Depending on your home's heating system, you may
need to change the jumper setting for the fan
operation. The jumper is located at the lower right-
hand side of the back of the thermostat.
HG – Use this setting for gas or oil-fired furnaces.
This setting allows the fan operation to be controlled
by the heating system; not the thermostat. This is the
correct setting for most systems.
HE – Use this setting for electric heating systems. With this setting, the thermostat will turn on the fan
immediately with the heating system.
The jumper is pre-installed in the 'HG' position as a factory default. So there is no need to change
the jumper if this is the correct setting.
To change the jumper setting, pull out the small black rectangular block and align it to the new
position and push it in fully.
RC
RH
Y
W
H2
H1
B
O
G
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw UPM THM302M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van UPM THM302M in de taal/talen: Engels als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van UPM THM302M

UPM THM302M Gebruiksaanwijzing - Français - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info