756407
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
EN 7
pyrometer TP10
Operation
Inserting the battery
Note
Make sure that the surface of the device is dry and the
device is switched off.
27
28
1. Open the battery compartment by folding open the
cover(28) with your fingers.
2. Use the battery clip(27) to connect the new
battery(1x 9V) with correct polarity.
3. Insert the battery in the battery compartment.
4. Close the cover of the battery compartment(28).
Carrying out a measurement
Ensure that the surface to be measured is free of dust, dirt
or similar substances.
To be able to gain exact measurement results on surfaces
which reflect heavily, stick matt masking tape to the
surface or apply matt black paint with a very high and
known degree of emission.
Note the 75:1 ratio of the distance to the measuring spot
diameter. For accurate measurements the measuring
object should be at least twice as large as the measuring
spot.
Please proceed as follows to carry out a measurement:
1. Point the device at the object to be measured.
2. Press the measurement button(7). Hold onto the
Measurement button(7) if you want to perform a
prolonged measurement.
ðThe device turns on and carries out a measurement.
ðThe SCAN symbol(12) appears in the display. The
currently measured value is indicated.
3. Let go of the Measurement button(7) again.
ðThe device stops measuring. The HOLD symbol(12)
appears in the display.
ðDepending on the setting of the device, either the
Max/Min value or the Avg/Dif value of the last
measurement will be displayed.
Settings
The bottom line of the display contains a three-part menu.
Within this menu different settings can be selected. You can
switch through the different menus using the Mode button(3).
Menu example:
MxMn Save Avg
The menu is controlled as follows:
The F1 button(4) selects the function on the left, MxMn in
our example.
The F2 button(5) selects the function in the centre, Save in
our example.
The F3 button(2) selects the function on the right, Avg in
our example.
Setting the Max/Min function
1. Repeatedly press the Mode button(3) until the MxMn Save
Avg menu is displayed:
ðThe MxMn Save Avg menu is shown on the display.
2. Press the F1 button(4) to select MxMn.
ðThe maximum value is displayed in the upper
measurement value display(18).
ðThe minimum value is displayed in the lower
measurement value display(20).
ðThe discrepancy between the current measured value
and the minimum value is indicated as deflection on the
scale(21).
Setting the Avg/Dif function
Please bear in mind, that the average value is continually
determined anew during a measurement, which means that
there can be deviations of the displayed Dif value in the in the
hundredth °C range.
1. Repeatedly press the Mode button(3) until the MxMn Save
Avg menu is displayed.
2. Press the F3 button(2) to select Avg.
ðThe average value is displayed in the upper
measurement value display(18).
ðThe difference between the current measured value to
the average value is displayed in the lower
measurement value display(20).
ðThe difference between the current measured value to
the average value is indicated on the scale(21).
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trotec TP10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trotec TP10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Trotec TP10

Trotec TP10 Gebruiksaanwijzing - Nederlands - 13 pagina's

Trotec TP10 Gebruiksaanwijzing - Deutsch - 13 pagina's

Trotec TP10 Gebruiksaanwijzing - Français - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info