775412
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
67
1. Remove the battery cover from the back
side of the computer using a
narrow flat blade screwdriver.
2. Install the battery so that the
positive "+" side of the battery is visible,
and replace the battery cover.
CAUTION: On the bottom of the computer
head next to the battery door is a small
recessed button. This is the Auto Clear
Button. Pressing this button will clear all
memories and reset all functions to their
default values.
All Clear Button
COMPUTER SET UP
Battery Installation
BUTTON FUNCTIONS
PROGRAMMING YOUR TREK
SENSOR CYCLE COMPUTER
Setting the Clock
1. Press the mode key to advance
to MXS/Clock display.
2. Press and hold the mode key for over 2
seconds until hours setting
begins to flash.
3. Press the adjust key to adjust hours
setting, press the mode key to confirm and
advance to minutes setting.
4. Press the adjust key (hold for fast
advance) to adjust the minutes, and press
the mode key to confirm setting and enter
normal display mode.
Mode Button
Adjust
Button
Setting Miles/ Kilometers and
Wheel Size
1. Press mode computer key to enter
AVS/ODO mode.
2. Press and hold mode key for over 2 sec-
onds until m/h begins to flash.
3. Press adjust key to select miles (m/h) or
kilometers (km/h) display.
4. Press mode key to confirm choice and
advance to wheel size setting.
5. Adjust the flashing digit with the adjust
button, confirm choice by pressing mode
button, and advance to next flashing digit.
6. Adjust and/or confirm all flashing
digits.
Wheel Size Setting
The wheel size setting number is equal to
the distance, in millimeters, that your front
wheel travels during one complete revolu-
tion. Each time the wheel magnet passes
the sensor unit on your fork, the sensor
sends an impulse to the computer telling it
that your wheel has completed one revolu-
tion. The computer calculates this distance
vs. time to give you accurate readings for
the various modes.
Determining Wheel Size Setting
There are three methods for determining the
wheel size setting. For the most accurate
computer readings, it is best to measure the
actual distance that your wheel travels in
one complete revolution. This method is
called a wheel roll out.
The Sensor is equipped with 2 buttons that
control the function of the unit.
1. MODE
Changes the Main Screens of the Sensor
2. ADJUST
Adjusts digits while programming and
activates ATM lap timer.
Perform the wheel roll out on a hard,
flat, smooth surface such as a garage or
basement floor.
Make sure your tires are properly inflat-
ed.
1. Position your bike so that the valve stem
of the front wheel is at its bottom most
position. Mark the spot on the floor directly
under the center of the valve stem using a
piece of tape or chalk.
2. Roll the bicycle forward in a straight line,
while putting downward pressure on the han-
dlebars to simulate rider weight. When the
wheel has completed one revolution and the
valve stem is at its bottom position, mark the
floor directly under the center of the valve
stem with tape or chalk. Measure the distance
between the two marks in millimeters. (Note:
Conversion of in. to mm. is 1 in.=25.4 mm.)
This is your wheel setting number. You can
repeat this procedure and average your results.
We recommend that you record your wheel set-
ting numbers here for future reference.
Method One: Wheel Roll Out
Sensor 1.0 97 6/12/00 11:17 AM Page 8
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trek 1997 sensor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trek 1997 sensor in de taal/talen: Engels als bijlage per email.

De handleiding is 0.09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info