775412
3
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
The Trek Sensor Computer attaches to
the mounting bracket by sliding the unit
onto the bracket from the back until it
snaps firmly into position. To remove the
computer from the bracket, place your
thumb against the back of the mounting
bracket and pull the computer toward you
with your index finger.
45
Maximum Speed (MXS)
The Maximum Speed reached during a ride is
displayed in 0.1 mi/Km increments on the
top line, with the MXS icon. Maximum
Speed is stored in
memory and is updated each time a new,
higher speed is reached.
CLOCK (CLK)
The 12 hour clock is displayed on the lower
line, indicated by the CLK icon.
ATM “Lap Timer” Display
A unique ATM “Lap Timer” display allows
you to lock the display at the end of a ride
segment and view the ATM, DST, AVS
and MXS at a later time.
This is especially useful at the end of a race,
allowing you time to cool down without
adding time to your Stopwatch.
As you cross the finish line, press the left
key for over 1 second to freeze information
on the display. You may continue to ride,
viewing the information locked on the flash-
ing locked display. The computer will con-
tinue to record information and store it in
memory. Press the left key to update the
current display information.
RESETTING THE COMPUTER
In SPD/ATM mode, press both keys for over
two seconds to clear ATM, DST, AVS and
MXS display.
SLEEP MODE
To conserve battery power, the computer
will enter the ‘Sleep’ mode after 5 minutes
of no speed input, blanking the display.
Press any key to enter normal operating
modes.
(Note: Unit will not enter sleep mode in
setting function mode.)
1. Position the sensor unit to the inside of
either the right of left fork blade
anywhere from 3-6 inches up from the fork
blade tip. Attach the sensor to the fork
blade with the quick ties but do not tighten
the ties completely until final adjustment is
complete.
INSTALLATION
Sensor and Wheel Magnet
2. Attach the wheel magnet to a spoke,
aligning the magnet with the sensor so it
faces and intersects the bottom polished
line on the sensor. The magnet should have
1-2 mm clearance from the sensor. If the
sensor and magnet are too close or touch-
ing, rotate the sensor unit toward the back
of the fork blade until adequate clearance is
achieved. Carefully tighten the quick ties
making sure you maintain the proper space
between the magnet and the sensor. Trim
the excess quick tie strap using a scissors
or fingernail clipper. Tighten the magnet
screw, but be careful not to over tighten as
this can damage the fitting.
Sensor Wiring and Bracket
1. Route the sensor wire up the back of the
fork blade or wind the wire around the
blade, making sure that the wire is not
loose and that you leave enough wire to
reach the handlebar. Secure the wire to the
fork blade immediately above the sensor
and at the top of the fork blade, using the
adhesive strips
that are provided or electrical tape.
2. Wind the wire upward around the front
brake cable until the wire is adjacent to the
handlebar, allowing enough slack for free
movement of the steering assembly cables.
3. Attach the bracket to the handlebar on
either side of the stem. The bracket goes
onto the handlebar with the wire toward the
rider side of the bar. Use the appropriate
rubber shim between the bracket and han-
dlebar to provide a secure fit.
Shims will
prevent slipping
Attaching the Computer to
the Bracket
Sensor 1.0 97 6/12/00 11:17 AM Page 6
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trek 1997 sensor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trek 1997 sensor in de taal/talen: Engels als bijlage per email.

De handleiding is 0.09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info