607819
7
Verklein
Vergroot
Pagina terug
1/102
Pagina verder
Try outother remote control keys to find outthe
range of functions you can control. If you think
that not all of the keys are active,repeat the pro-
cedure of this programming method to find out
the code supporting a wider range of features.
Method D - Automatic code search
With this method, the remote control scrolls
through the full code list by sending an IR signal
to the set to be controlled remotely. Proceed as
follows:
1. Check that your equipment is on. If not,
switch it on manually.
2. Hold the
SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit (the indicator lamp
remains lit for several seconds in order to let
you continue with the following steps. The
blinking of the indicator indicates the end of
the available time,then it goes out).
3. Release the
SETUP key.
4. Press the key corresponding to the type of
equipment (for example
TV).
5. Press the PROG .key once.After a few
seconds the remote control begins to list all
the codes included in the library (around 1
code per second). Press
PROG a second
time to reduce the speed of the test (1 code
every 5 seconds).As soon as the device chan-
ges channel you must immediately press
OK
to record the code and stop the listing.If you
don’t react quickly enough, simply return to
the previous code by pressing
PROG (you
can restart the forward listing by pressing
PROG .As soon as the device reacts again,
press
OK to record the code.
Method E Programming for
control of a COMBO (combined TV-
VCR, TV/DVD, VCR/DVD, set)
Depending on the COMBO group (TV/VCR,
VCR/DVD,etc.) and the make,you will be requi-
red to enter a single code for both devices in the
COMBO,or to enter two codes, one code per
device.Consult the separate list to discover this.
Before you start programming,you must find the
subcode or code of the subset to be controlled
(television or video recorder).
Refer to the list supplied with this user manual
(see page subcodes or codes).
1. Switch on the COMBO you want to control.
2. Hold the
SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit.
3. Press the key of the first device to control,
and then follow one of the programming
methods A, B,C or D previously described.
4. Ifa second codeprogrammingis required,then
repeat steps 2 and 3 above.
How to retrieve a programmed
code?
It may be useful to retrieve the code program-
med in the remote control.
1. Hold the
SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit.
2. Press the key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO: Hifi
system.
3. Press the SETUP key briefly, so that the last
mode selected blinks once.
4. Press the numbered keys in ascending order
(0 to 9) until the selected mode blinks once.
5. The digit that makes the selected mode flash
is the first of the 4 digits in your code.Make
a note of it.
6. Repeat step 4 to find out the other numbers
of the code.
7. Once you have found the fourth digit, the
selected mode indicator goes off.
Check of the programming
•For a television or a satellite receiver:switch on and,
for example,press 2 to change channels.
•Video recorder:load a tape and then press .
•DVD player:load a DVD and then press .
Tr
y
other
re
mote
contr
ol
ke
ys
to
fi
nd
out
the
ra
ng
e
of
functions you can control.If you think that not all of the
keys are active,try the programming Method B or C.
Whenyou have retrievedthecodeof your set,jot itdown
so that you can use it whenever needed.
Programming a sequence
of commands (Macro)
The MACRO key in coordination with one of the
keys A, B,or C allows the programming and
memorisationof up to 3 command sequences(the
automatic and successive pressing of several keys
of your choice). Thus any sequence of key com-
mands can be reduced to merely 2 commands
(MA
CRO key + A, B,or C key). For example after
programming,by pressing MACRO then keyA you
could turn on your television set,turn on your
satellite or cable receiver,zap to a preferred chan-
nel,turn on your video cassette recorder and start
a recording session (providing a cassette was pre-
viously loaded).You can memorise a sequence of
10 commands with each A, B,or C key.
3
EN
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thomson ROC 4505 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thomson ROC 4505 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info