607819
6
Verklein
Vergroot
Pagina terug
1/102
Pagina verder
Note 2:To control 2 devices of the same type and same
make (2Thomson video cassette recorders, 2 Thomson
satellite receivers, etc.) first make sure that these two
devices have been already adjusted to react to different
subcodes (A and B codes onThomsondevices).Thensuc-
cessively program 2 mode keys using method D.
Programming
the remote control
Method A Fast programming with
1-digit subcode
Before you start programming,you must find the
subcode of the set to be controlled.
Refer to the list provided with these instructions,
page I of the subcodes.
1. Switch on the set you want to control.
2. Hold the SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit (the indicator lamp
remains lit for several seconds in order to let
you continue with the following steps.The
blinking of the indicator indicates the end of
the available time,then it goes out).
3. Pressthe key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO: Hifi
system.
4. While the indicator is lit,type in the subcode
(example:1 forTHOMSON).
5. Direct the remote control towards the set
andtryto switch itoff by pressingthe key.
6. If the set you want to control switches off,
press OK to memorise the subcode.
7. Should the set not switch off, press key,
repeatedly,until the set switches off.Between
twokeypresses,leaveenoughtime for thekey
corresponding to the selected mode enough
time to light up again (about 1 second).
Proceeding this way will enable you to see
whether the set responds or not.
8. Immediatelyuponthe switching-offof the setto
be controlled,press
OK to store the subcode.
Check of the programming
In principle,your set is ready for receiving the remote
controlcommands.Check your remote control forproper
functioning by performing the test described on page 3.
Method B 4-digit codes
Programming
Before you start programming,you must find the
code of the set to be controlled.
Refer to the list provided with these instructions,
page II of the codes.
1. Switch on the set you want to control.
2. Hold the SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit (the indicator lamp
remains lit for several seconds in order to let
you continue with the following steps. The
blinking of the indicator indicates the end of
the available time,then it goes out).
3. Pressthe key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO:Hifi
system.
4. While the indicator is lit,enter the first digit
ofthe 4-digit codeproposedfortheset to be
controlled (example:0036 forThomson).
5. Direct the remote control towards the set
andtryto switch itoff by pressingthe key.
6. Should the set not switch off,repeat step 2.
Then type in the next 4-digit code.Try to
switch off the set by pressing key once.
Repeat this procedure by trying out each of
the 4-digit codes.
Check of the programming
In principle,your set is ready for receiving the remote
controlcommands.Check your remote control forproper
functioning by performing the test described on page 3.
Method C Programming by means
of code retriever
Should none of the codes work,you still have the
possibility of retrieving the appropriate code
without having to perform any input.
1. Switch on the set you want to control.
2. Hold the SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit
3. Pressthe key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO:Hifi
system.
4. Direct the remote control towards the set
and try to switch it off by pressing the
key.
5. If the set you want to control switches off,
press
OK to memorise the subcode.
6. Should the set not switch off,press key, as
many times as required (up to 200 times),until
the set switches off.Between two key presses,
leave enough time forthe key corresponding to
theselectedmode enoughtime tolightup again
(about 1 second).Proceeding this way will ena-
bleyoutoseewhetherthe setrespondsornot.
7. Immediatelyupon the switching-off of the set
to be controlled,press
OK to store the code.
Check of the programming
In principle,your set is ready for receiving the remote
controlcommands.Check your remote control forproper
functioning by performing the test described on page 3.
2
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thomson ROC 4505 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thomson ROC 4505 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info