622559
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Before finally closing the safe, it is advisable to check that everything is OK by
operating the opening and closing mechanism a number of times with the door open.
Then shut the door and turn the knob anticlockwise until it is closed
OPENING THE SAFE USING YOUR PERSONAL CODE
Press “ON”
Enter your personal code set earlier and press “ENTER”. The green “OK” LED lights up for five
seconds. Within this time, turn the knob clockwise and open the door
SIGNAL INDICATING THAT INTERNAL BATTERY(ES) ARE GOING FLAT
When the internal battery begins to go flat, this is indicated at the end of the opening procedure, by the red
“BATTERY” LED lighting up and a low beep tone. At this point, it will still be possible to open the safe a
number of times. Replace the internal batteries.
EMERGENCY OPENING WITH INTERNAL BATTERY(ES) FLAT
If the failing battery(es) goes completely flat, as soon as the keyboard is pressed, to proceed with opening the
safe, it is necessary to use a new 9-volt LR61 alkaline battery externally (see Pic. 2)
Press the 9-volt battery contacts firmly on the corresponding contacts on the keyboards, ensuring that they
are positioned correctly (the “-“ of the battery touching the bigger contact and the “+” of the battery touching
the small contact). With the battery firmly in position, key in code and open door. Replace internal batteries
immediately.
CAUTION
Wall safes: After installing the safe in the wall, leave the safe open for a few days allow any
dampness to dry out.
Replace alkaline batteries every year.
It must be remembered that even new, packed batteries can sometimes be defective, for various
reasons, or have a brief duration. In the event of failure of the magnet release, or other faults, first of
all, replace the battery with a new alkaline batteries.
The manufacture declines all responsibility for failure to observe the instructions given, or for
improper use of the safe, thus causing the warranty to lapse.
Versions with EMERGENCY KEY
OPENING WITH EMERGENCY KEY
Remove the adhesive label marked with the letter “E” (Pic.3).
Insert the key and open the lock up to the stop point.
Open the door.
Once the door is open, turn the knob anticlockwise until the bolts are fully extended.
Close the lock and remove the key.
WARNING!
NEVER LEAVE YOUR
EMERGENCY KEY IN THE
SAFE
PROGRAMMING
BUTTON
р
iс. 1
BATTERY CASE
REMOVE
р
iс. 3
ADESIVE LABEL
FOR EMERGENCY
KEY
рiс. 2
CONTACT PAD
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Technomax SMT tot 2009 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Technomax SMT tot 2009 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Technomax SMT tot 2009

Technomax SMT tot 2009 Gebruiksaanwijzing - Nederlands - 2 pagina's

Technomax SMT tot 2009 Gebruiksaanwijzing - Deutsch - 2 pagina's

Technomax SMT tot 2009 Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info