565040
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
The home technology brand for the entire house. More information at www.sygonix.com
GB
Operating instructions
Thermostat “tx.2“, AP
Intended use
The product is used for the temperature control in living areas and of ces.
Depending on the device connected, you can switch between the heating or cooling
function using a sliding switch.
The other sliding switch is used to select the overnight temperature reduction (night
setback) or to turn it on or off (2 °C or 5 °C can be selected).
An LC display indicates the room temperature and the operating mode.
Always observe the safety instructions and all other information included in these op-
erating instructions!
Any other use than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, re, electric shock, etc. No part of the
product may be modi ed or converted!
This Product Meets Legal, National and European Requirements. All names of com-
panies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Thermostat
• Operating Instructions
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates speci c risks associated with handling, function and
use.
Safety Instructions
Read the complete operating manual carefully before using the product,
as it contains important information about the correct installation and
operation.
The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any
consequential damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! The
warranty will be void in such cases!
Caution!
This device should be installed only by people with relevant electrotech-
nical knowledge and experience!
With an improper installation, you risk:
- Your own life;
- The life of the user of the electrical system.
With an improper installation, you risk severe material damage, e.g. through
re. Yo u face the risk of personal liability for damage to people and material.
Contact an electrician!
The unauthorised conversion and/or modi cation of the product is not al-
lowed for safety and approval reasons (CE).
The product is not a toy and must be kept out of the reach of children! There
is a risk of a lethal electric shock!
The product may only be operated on the mains voltage (see section “Tech-
nical Data”). Never try to operate the product at another voltage as this will
cause its destruction.
This product is only to be installed and used in dry conditions indoors. The
product must not get damp or wet as this may damage it; danger of a fatal
electric shock!
Do not use this product in rooms or under adverse ambient conditions
where combustible gases, vapours or dust are or may be present! There is a
risk of explosion!
The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
If you have reason to assume that safe operation is no longer possible, dis-
connect the product immediately and secure it against inadvertent opera-
tion. After this, let an expert check the product.
It can be assumed that safe operation is no longer possible if:
- the product shows visible signs of damage,
- the product does not work at all or works poorly ( ickering light, leaking
smoke or a smell of burning, the light ickers, audible cracking noises,
discolouration to the product or the adjacent surfaces.)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
In commercial institutions, the accident prevention regulations of the Em-
ployer’s Liability Insurance Association for Electrical Systems and Operating
Facilities are to be observed!
If you have any questions that are not answered in this manual, please con-
tact our technical service or another specialist.
Preparations for connection and installation
The device must be voltage-free during installation and connection.
Turn the power off and ensure that none of the poles is carrying a current by remov-
ing the electric circuit's fuse, or switching off at the circuit breaker. Secure it against
unauthorised reconnection, e.g., with a danger sign. In addition, switch off the as-
sociated ground fault circuit interrupter (breaker).
Check that the mains cable is free of current e.g. with an appropriate tester.
Choose a suitable place for installation. In order to ensure a correct functioning of
the thermostat, it must be mounted so that it is not located near to heating appli-
ances, windows, doors etc. Keep the thermostat away from draught too.
Don't mount the thermostat behind furniture or curtains.
Since the exterior walls of buildings are usually colder than the interior ones (de-
pending on the insulation of the building), the thermostat should not be mounted
there either.
Wall heaters function with air convection. In the process, the warm air rises from the
heater, cools down slowly and decreases on the other side of the room. Thus, the
ideal location for the installation of the thermostat would be the wall opposite to the
heater. The ideal mounting height is approx. 1.5 m.
Installation and Connection
Observe the chapter “Safety instructions” and the chapter “Prepara-
tions for connection and installation”.
First switch off the mains voltage to all poles.
Remove the wall mounting plate on the back of the device by unscrewing the two
fastening screws at the bottom edge.
You will nd the temperature sensor on the rear of the
room temperature regulator, which is attached by two
spring clips (see picture right).
If desired, you can replace these internal sensors with
an external sensor (this is not included in the room
temperature regulator package; it can be ordered se-
parately).
Pull the two-poled spring clips from the contact pin, to
attach easily, and then loosen the two screws, which
attach the sensor and take out the sensor. Keep this
for later use.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sygonix TX 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sygonix TX 2 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info