733469
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Page 20 of 20
Rear brake housing routing (internal)
1
C
A
D
B
2
Run the brake housing starting from the bottom (fig.1). Insert the housing into the port below the shock link
A
(fig.1), on the non-drive-side.
Continue running the housing into the frame until it exits at the head tube port
B
(fig.2).
Bolt the brake to the frame, then bolt the seatstay cable guide (S156500003)
C
to the seatstay (fig.1) to position the housing against the frame.
Trim the housing to the required length, attach the housing to the brake caliper and bleed the brake according to the manufacturer’s instructions.
Install the housing stop (S156500003)
D
in the same way as for the derailleur housing (P.19). Tighten the bolt (M4 x 13mm) just enough so that the
housing can’t move.
Rear brake housing routing (external)
1
A
B
C
D
2
The housing is attached to the side of the frame at four contact points (cable housing kit S156500003):
Seatstay
A
: Attach the brake, then bolt the supplied cable guide (fig.1) to the seatstay to position the housing against the frame.
Below shock link
B
: Using the Internal routing guide as a base, mount the external routing guide, then insert a longer bolt (M4 x 18mm).
Forward shock eye bolt
C
: Place the supplied retainer loop over the housing (fig.1), then attach it to the frame by placing it on the forward
shock eye bolt. Tighten the forward shock eye bolt to 170 in-lbf (19.2 Nm).
Down tube @ head tube
D
: Bolt the supplied cable guide (fig.2) to the frame to position the housing against the frame.
Trim the housing to the required length, attach the housing to the brake caliper and bleed the brake according to the manufacturer’s instructions.
Rear axle installation
1
A
2
B
3
C
Insert the axle (S150200001)
A
through the non-drive-side dropout (fig.1), hub and drive-side dropout. Make sure the axle head is aligned.
Install the derailleur guard (S159900013)
B
(fig.2), then tighten the derailleur guard bolt to tighten the axle. Torque to 30 in-lbf (3.4 Nm).
Tighten the two hanger bolts (S152600001)
C
(fig.3). Make sure the gaps between the dropout and the hanger are even. Torque to 55 in-lbf (6.2 Nm).
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Specialized FSR - 2015 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Specialized FSR - 2015 in de taal/talen: Engels als bijlage per email.

De handleiding is 14,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info