733469
21
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Page 19 of 20
DEMO 8 CARBON
Bottom Bracket Installation
A A
B
B
C
D DE E
G
F
1
H
2
Press the BB30 bearings
A
(S091600016, 42mm x 30mm x 7mm) into the left and right sides of the BB shell/axle (S150400007)
B
(fig.1).
Install the inner spacer (S150400008)
C
, bearings (S150600002)
D
and outer spacers (S150400006)
E
into the shell of the frame (fig.1).
Align the main pivot holes
F
of the chainstay assembly with the shell of the frame
G
, then slide the BB shell/axle through the drive-side chainstay
hole and the shell of the frame (fig.1).
Thread the axle into the non-drive-side chainstay hole, using the supplied main pivot lock tool
H
(fig.2).
I
3
4
With the main pivot lock tool (S150400002)
H
positioned with the lip facing out, tighten the bottom bracket by inserting a long 6mm Allen key or
a screwdriver shaft
I
into the holes in the lip and rotate counter-clockwise (fig.3). Once tension is felt, rotate the splined ring an additional 1/4-turn.
Fig.4: Once tight, flip the pivot lock tool around so that the lip is positioned over the lower corner of the chainstay and lock it in place by inserting
three screws into the ISCG tab holes (fig.4). If desired, install a chainguide/bashguard assembly before inserting the bolts.
NOTE: Certain chainguides might interfere with the lip portion of the pivot lock tool. In the case of interference, use the flat lock tool (S150400001).
Derailleur cable routing
1
A
B
C
E
2
D
Insert a full-length piece of derailleur cable housing, measuring at least 6’ (1800mm) long, starting at the rear derailleur port
A
(fig.1).
Guide the housing up the seatstay until it exits through the upper seatstay port
B
(fig.1). Make sure the seatstay protector (S159900014) is installed.
Insert the housing into the port below the shock link
C
(fig.1). Continue running the housing into the frame until it exits at the head tube port
D
(fig.2).
Trim the housing to the required length, install the cable and adjust the derailleur, all according to the manufacturer’s instructions.
Install the housing stop assembly (S156500003)
E
(fig.1). Tighten the bolt just enough so that the housing can’t move.
Rubber pad
Cable guide
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Specialized FSR - 2015 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Specialized FSR - 2015 in de taal/talen: Engels als bijlage per email.

De handleiding is 14,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info