718540
17
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
1- Raise the needle by turning hand wheel toward you and lower the
presser foot.
2- Rotate the needle clamp screw toward you (counter-clockwise) to
loosen the needle
3- Remove the needle from the clamp
4- Insert the new needle into the needle clamp with the  at side away
from you
5- When inserting the needle into the clamp, push it up as far as it will
go.
6- Tighten the clamp screw clockwise  rmly with the screwdriver
- Note: Check you needles frequently for barbed or blunted points.
Snags and runs in knits,  ne silks and silk- like fabrics are permanent
and are almost always caused by damaged needle.
Thread and needle chart
- Use the standard needles. The size of your needle should match the
size of the thread and both should match the fabric.
- For normal sewing, the same size and type of thread should be used
in the bobbin as on the upper part of the machine
Never use a bent of dull needle.
Kind Fabric Threads Needle Size
Light
Weight
Crepe de chine,
Voile Lawn,
Organdy,
Georgette,
Tricot
Fine Silk,
Fine Cotton,
Fine Synthetic,
Fine Cotton Cov-
ered Polyester
9 or 11
Medium
weight
Lines,
Cotton,
Pique,
Serge,
Double knits,
Percale
50Silk,
50~80 Cotton,
50~60 Synthetic,
Cotton Covered
Polyester
11 or 14
Heavy
Weight
Denim,
Tweed,
Gabardine,
Coating,
Drapery and
Upholstery
Fabric
50 Silk,
40~50 Cotton,
40~50 Synthetic,
Cotton Covered
Polyester
14 or 16
Setting Spool Pins:
- The spool pins are used for holding the spool of thread in order to feed
thread to the machine.
- To use, pull up the spool pin, Push down for storage
- NOTE: In case of using thread which has tendency to tangle around
the spool pin, thread through the hole of spool pin as shown. The hole
should face to the thread spool.
Removing or replace the bobbin case:
Refer to remove the Extension table, raise the needle by turning
the hand wheel toward you, then open the shuttle cover.
- Take out bobbin case holding the latch.
- When inserting the bobbin case, place the horn into the recess of the
shuttle race.
- Caution: Be sure to disconnect the power supply before operating the
machine
Winding the bobbin :
1- Draw the thread from spool. Guide the thread around the bobbin
winder thread guide. Insert the thread through one of holes in the bob-
bin from the inside to the outside. Put the bobbin on the bobbin winder
spindle.
2- Pull out the hand wheel.
3- Push the bobbin case to the right. With the free end of the thread
held in your hand, depress the foot control. Stop the machine when it
has made a few turns, and cut the thread close to the hole in the bob-
bin. Depress the foot control again.
- When the bobbin is fully wound, it will stop automatically.
- Return the bobbin winder to its original position by moving the spindle
to the left, and cut the thread. Push back the hand wheel.
Threading bobbin case
1- Place the bobbin into bobbin case. Make sure the thread unwinds in
the direction of arrow.
2- Pull the thread into bobbin case slot.
3- Draw the thread under the tension spring and into the delivery eye.
Leave about 10cm (4 inches) of free thread.
Threading the machine
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solac SW8240 - Cotton 24.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solac SW8240 - Cotton 24.0 in de taal/talen: Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 7,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info