758612
13
Verklein
Vergroot
Pagina terug
1/144
Pagina verder
13
-with depth stop turret G the routing depth can be
increased by steps respectively (recommended for
deep cuts)
! re-adjust the routing depth after having changed
router bits
Speed control 9
For optimal routing results on dierent materials
-select routing speed with wheel K (also while tool is
running)
-use table q as reference for determining the right
routing speed
-before starting a job, nd the optimal speed by testing
out on spare material
! after longer periods of working at low speed,
allow the tool to cool down by running it for
approximately 3 minutes at high speed with no
load
LED-light AD w
-LED-light AD automatically lights on when activating
trigger M
Dust suction
-mount vacuum cleaner adapter L as illustrated ea
-connect vacuum cleaner hose to vacuum cleaner
adapter L eb
Operating the tool r
! 
! while working, always hold the tool at the grey-
coloured grip area(s)
-place tool on workpiece
-switch on tool by rst pressing knob N (= safety switch
which cannot be locked) and then pulling trigger M
! before the router bit reaches the workpiece, the
tool should run at full speed
-loosen locking lever J and slowly push tool down until
depth gauge D reaches depth stop turret G
-tighten locking lever J
-carry out the routing procedure with uniform feed rate
-use the tool with its base-plate at on the workpiece
-as a general rule one should pull the tool, not push it
-after nishing the work, loosen lever J and guide the
tool back into the upper starting position
-release the trigger M
Proper guiding t
-keep in mind that router bit turns clockwise
-guide tool so that bit turns into the workpiece, not away
from it
Mounting adapter plate P (for copying with a template) y
Mounting parallel guide Q u
-insert parallel guide rods Y through holes in base-plate
R
-slide parallel guide to desired width and fasten it with
2 knobs Z
Using the parallel guide as a circular guide i
! 
-fasten pin AA with nut AB as illustrated
-insert rods Y into base-plate R
-pierce pin AA into marked centre of circular arc
-fasten parallel guide with 2 knobs Z
-guide the tool with consistent feed across the
workpiece
Using the parallel guide with curve buer W o
-mount curve buer W (with guide roller mounted) as
illustrated
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Mounting/removing router bits 6
! 
! ensure that router bit shaft is perfectly clean
! ensure that collet size (6 mm, 6.35 mm, 8 mm)
corresponds with shaft size of router bit
-turn tool upside down
-lock shaft by pushing shaft lock A (rotate collet nut B, if
necessary) and hold it while you
FOR MOUNTING:
-loosen collet nut B with wrench C
-insert bit with a little space x in collet 7
-tighten collet nut rmly with wrench C
-release shaft lock A
FOR REMOVING:
-loosen collet nut B with wrench C
-remove bit
-release shaft lock A
! for loosening router bit it may be necessary to
tap at the top of the router bit, using hammer and
piece of wood to protect the bit
! never tighten collet nut, if there is no router bit in
collet; collet may be damaged
Changing collets 7
! 
! ensure that collet shaft is perfectly clean
-loosen collet nut B 2 or 3 turns
-tap collet nut B with wrench C
-remove collet nut B and collet (lock shaft)
-turn tool upside down
-insert new collet in collet shaft
-mount collet nut B (lock shaft)
! never tighten collet nut, if there is no router bit in
collet; collet may be damaged
Adjusting routing depth 8
! 
-set the ne-adjustment to its center position by turning
knob E until the end, then turn back 4 full turns and set
the scale F to 0 8a
-rotate turret G so that its lowest position clicks into
place right under depth gauge D (for zeroing) 8b
-loosen knob H so that depth gauge D drops onto depth
stop turret G 8b
-place tool on workpiece
-loosen locking lever J 8c
-push tool down until router bit is in contact with
workpiece 8d
-release and tighten locking lever J 8e
-move depth visor AC to 0 mm 8 f
-raise depth gauge D as many mm as the desired
routing depth, and tighten knob H 8f
-loosen locking lever J and guide the tool back up again
-use ne-adjustment knob E for setting the routing depth
more precisely (0..±8 mm); the marks on the scale F
correspond with 0.1 mm, 1 full turn corresponds with
2.0 mm
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 1860 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 1860 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 7,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info