616706
58
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
56
HELPFUL MESSAGES
Messages are displayed with LED lamps above the stitch selection panel on the machine.
When a message is displayed, you may x the problem by following the correction suggestion most suited to your issue.
The corrections are preceded by an arrow.
SYSTEM ERROR
All system error corrections are as follows.

Turn off and on the power switch to eliminate the problem that caused the system error to occur.
If the error number should not disappear, consult an authorized technician.
Helpful message
on control panel
Problem
Correction
1. The bobbin winder shaft is in the incorrect position for the function you have selected.
Position the bobbin winder shaft to the left position for sewing and to the right position for
bobbin winding.
2. The reverse button is pressed during bobbin winding.
Do not press reverse button during bobbin winding.
1. Buttonhole stitch is selected on the stich control panel; however the buttonhole lever is not
in the correct position.
Lower buttonhole lever and begin sewing the buttonhole.
2. A stitch pattern is selected; however the buttonhole lever is engaged (lower position).
Raise buttonhole lever and begin sewing.
3. The buttonhole lever is in an incorrect starting position.
Lower the buttonhole lever so that it drops down vertically between the stoppers. See page
46 for details.
1. Something other than foot control is detected in the machine socket for the foot control.
Remove foreign particle from socket.
2. Foot control is connected or disconnected.
This is not an error message. It only indicates the connection or disconnection of the foot
control and the C3 message will disappear in a few seconds. No correction is needed.
1. Machine does not operate due to thread tangles in bobbin case or jamed fabric.
Turn off power switch and eliminate the problem that caused the machine to stop.
1. The stitch pattern selected, does not operate when the reverse/tacking stitch is pushed.
Select a stitch pattern that can be operated in the reverse/tacking stitch mode.
1. The top thread has broken.
Lift presser foot lifter. Pull to remove top thread from machine and rethread.
1. The foot controller was pushed down to start sewing before the presser foot was lowered.
Lower presser foot and begin sewing.
Misfunction of main shaft motor.
Abnormal signal from bobbin winder shaft.
Abnormal signal from cam sensors.
Reverse stitch button is engaged, when the power is tuned on.
58

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Singer-160

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Singer 160 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Singer 160 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 10,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info