782500
26
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
26 GB
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be xed in the outer
position on both sides. (see Fig. 11)
Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) outwards.
The moveable stop rail (28) must be locked in a posi-
tion far enough from the inner position that the dis-
tance between the stop rail (28) and the saw blade
(7) is no more than 8 mm. (see Fig. 12)
Before making the cut, check that no collision could
occur between the stop rail (28) and the saw blade (7).
Tighten the set screw (29) again.
Loosen the locking handle (13) counterclockwise and
pull the indexed position lever (12) with the index n-
ger at top.
Set the turntable (16) to the desired angle by using
the locking handle (13). The pointer (14) on the turn-
table (16) must match with the desired angular scale
(15) on the xed saw table (17).
Turn the locking handle (13) clockwise tox the turn-
table (16).
Cut as described under section 8.4.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/11-14)
The crosscut saw can be used to make mitre cuts of 0°
- 45° to left/right in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28a/28b) must be xed at
the outer position.
Open the locking screw (29) for the adjustable stop
rail (28) and push the adjustable stop rail (of inclined
side) outwards. (see Fig. 13+14)
The other adjustable stop rail (28) must be xed far
enough in front of the innermost position that the dis-
tance between the stop rail (28) and the saw blade (7)
amounts to a maximum of 8 mm. (see Fig. 12)
Before making a cut, check that the stop rail (28) and
the saw blade (7) cannot collide.
Secure the locking screw (29) again.
Move the machine head (5) to the top position.
Fix the rotary table (16) in the 0° position.
Loosen the locking lever (22) and use the handle (1)
to angle the machine head (5) to the left/right, until
the pointer (20) indicates the desired angle measure-
ment on the scale (19).
Re-tighten the locking lever (22).
Cut as described in section 8.4.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1-2/11-14)
The crosscut saw can be used to make mitre cuts to the
left/right of 0°- 45° in relation to the work face and, at
the same time, 0°- 45° to the left or 0°- 45° to the right
in relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be xed at the
outer position.
Open the locking screw (29) for the adjustable stop
rail (28a/28b) and push the adjustable stop rail (of in-
clined side) outwards. (see Fig. 13+14)
The other adjustable stop rail (28) must be xed far
enough in front of the innermost position that the dis-
tance between the stop rail (28) and the saw blade (7)
amounts to a maximum of 8 mm. (see Fig. 12)
Before making a cut, check that the stop rail (28) and
the saw blade (7) cannot collide.
Secure the locking screw (29) again.
Move the machine head (5) to its upper position.
Loosen the locking handle (13) counterclockwise and
pull the indexed position lever (12) with the index n-
ger at top.
Set the turntable (16) to the desired angle by using
the locking handle (13). The pointer (14) on the turn-
table (16) must match with the desired angular scale
(15) on the xed saw table (17).
Turn the locking handle (13) clockwise tox the turn-
table (16).
Loosening the locking lever (22).
Use the handle (1) to angle the machine head (5) to
the left/right, until the pointer (20) indicates the de-
sired angle measurement on the scale (19). (in this
connection see also section 8.6).
Re-tighten the locking lever (22).
Cut as described under section 8.4.
8.8 Limiting the cutting depth (Fig. 3)
The cutting depth can be innitely adjusted using the
screw (26). To do this loosen the knurled nut on the
screw (26). Move the stop for the cutting depth limi-
tre (27) to the outside. Turn the screw (26) in or out
to set the required cutting depth. Then re-tighten the
knurled nut on the screw (26).
Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (21) for sawdust
and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (21) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 15-18)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
Blade guard (6) open
Loosen the screw (36)
Blade guard (6) upwards until it is held
Firmly press the saw shaft lock (4), and slowly turn
theange screw (32) clockwise. After max. one turn,
the saw shaft lock (4) engages.
Then undo the ange screw (32), by applying a slight-
ly greater force in a clockwise direction.
Fully unscrew the ange screw (32) and remove the
outer ange (33).
Then remove the saw blade (7) from the innerange
(39) and pull out in a downwards direction.
Carefully clean the ange screw (32), outer ange
(33) and inner ange (39).
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HM120L Redstone bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HM120L Redstone in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 3,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info