782500
25
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
25GB
8. Attachment and operation
8.1 Attaching the saw (Fig. 1/2/6a-c)
To adjust the turntable (16) turn the locking handle
(13) clockwise to release the lock.
Slide the locking position lever (12) upwards. To do
this, take your index nger.
Now adjust the turntable (16) and pointer (14) by use-
ing the required angle of the scale (15). Fix it by turn-
ing the locking handle (13) counterclockwise.
Pressing the machine head (5) lightly downwards and
removing the locking bolt (24) from the motor bracket
at the same time disengages the saw from the low-
est position.
Swing the machine head (5) up until the release lever
(3) latches into place.
It is possible to secure the clamping device (8) to the
left or right on the stationary saw bench (17).
Attach the workpiece supports (9) to the xed saw
table (17) as shown in Figure 6a,b,c and push all the
way through. Secure the shafts with the screws to
prevent them from slipping out accidentally. Then fas-
ten in the desired position with the screw (10).
Install anti-tilt (42) on the xed saw table (17) and
push it completely. (See Fig. 6c) Secure the shaft with
a screw (42a) against loosening.
The machine head (5) can be tilt left or right to max.
450 by opening the locking handle (22).
8.2 Precision adjustment of the stop for crosscut
90° (Fig. 1/2/5/7/8)
No stop angle (a) included.
Lower the machine head (5) and secure using the
locking bolt (24).
Loosen the locking lever (22).
Position the angle stop (a) between the saw blade (7)
and the rotary table (16).
Flip stop plate 900 (40) at top
Slacken the counternut (Fig. 8 Pos. d). Adjust the ad-
justing screw (30) until the angle between the saw
blade (7) and rotary table (16) is 90°.
Retighten the counternut (d) to secure this setting.
Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (20) using a
Philips screwdriver, set to position 0° on the angle
scale (19) and re-tighten the retaining screw.
8.3 Precision adjustment of the stop for mitre cut +45°/-
45° (Fig. 1/2/5/9/10)
No stop angle (b) included.
Lower the machine head (5) and secure using the
locking bolt (24).
Fix the rotary table (16) in the 0° position.
Loosen the locking lever (22) and use the handle (1)
to angle the machine head (5) 45° to the left or right.
45° - position angle stop (b) between the saw blade
(7) and rotary table (16).
Slacken the counternut (c). Adjust the adjusting screw
(31) until the angle between the saw blade (7) and ro-
tary table (16) is precisely +4/-45°.
Retighten the counternut (c) to secure this setting.
8.4 Cross cut 90° and turntable 0° (Fig.1/2/11/12)
In the case of cutting widths up to approx. 100 mm it is
possible to x the traction function of the saw with the
set screw (23) in the rear position. In this position the
machine can be operated in cross cutting mode. If the
cutting width is over 100 mm then it is necessary to en-
sure that the set screw (23) is loose and the machine
head (5) can move.
Attention! For 90° mitre cuts, the moveable stop
rail (28) must be xed in the inner position on both
sides. (see Fig. 11)
Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) inwards.
The moveable stop rail (28) must be locked in a posi-
tion far enough from the inner position that the dis-
tance between the stop rail (28) and the saw blade
(7) is no more than 8 mm. (see Fig. 12)
Before making the cut, check that no collision could
occur between the stop rail (28) and the saw blade
(7).
Tighten the set screw (29) again.
Move the machine head (5) to its upper position.
Use the handle (1) to push back the machine head
(5) and x it in this position if required (dependent on
the cutting width).
Place the piece of wood to be cut at the stop rail (18)
and on the turntable (16).
Lock the material with the clamping device (8) on the
xed saw table (16) to prevent the material from mov-
ing during the cutting operation.
Push down the release lever (3) to release the ma-
chine head (5).
Press the ON/OFF switch (2) and the unlocking
switch (2a) to start the motor.
With the drag guide (23) xed in place:
use the handle (1) to move the machine head (5)
steadily and with light pressure downwards until the
saw blade (7) has completely cut through the work
piece.
With the drag guide (23) not xed in place:
pull the machine head (5) all the way to the front.
Lower the handle (1) to the very bottom by applying
steady and light downward pressure. Now push the
machine head (5) slowly and steadily to the very back
until the saw blade (7) has completely cut through
the work piece.
When the cutting operation is completed, move
the machine head (5) back to its upper (home)
position and release the ON/OFF button (2).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not re-
lease the handle (1) after completing the cut; instead
allow the machine head to move upwards slowly
whilst applying light counter pressure.
8.5 Cross cut 90° and turntable 0°- 45° (Fig.
1/2/11/12)
The crosscut saw can be used to make crosscuts of
0°-45° to the left and 0°-45° to the right in relation to
the stop rail.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HM120L Redstone bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HM120L Redstone in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 3,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info