781483
37
Verklein
Vergroot
Pagina terug
1/184
Pagina verder
37
Switching on and off, Fig. 23
Make sure that all keys and adjusting tools are well away
from the spare desk that the attitudes are installed in full
and all safety covers are kept.
O - Out
I - On
This machine uses an electromagnetic switch for op-
timal security. Whenever the current is interrupted the
machine stops immediately. To restart the machine the
green button must be pushed again
Utilization of the machine
Fit and secure the cutting knives.
Adjust the speed, and adjust the output fence in such
a way that the material cut is supported and a com-
pensation for the material removed is achieved.
Switch the machine on.
Make sure the work piece is rmly pressed against
the fence.
Push the work piece softly from right to left against the
turning direction of the tool.
Keep your forwarding speed constant. Do not push too
fast – it would slow down the motor too much.
Feeding the work piece too fast will result in a poor
cutting quality. There is also the risk of damaging the
cutting knives or the motor.
Feeding the work piece too slow will result in burnt
spots on the work piece.
With very hard wood and important cuts it can be nec-
essary to work progressively in several cuts until the
desired depth is achieved.
The correct intake speed depends on the cutter size,
the material type of the work piece, and the cutting
depth. It is recommended to practise rst with a piece
of scrap wood in order to determine the correct intake
speed and the dimensions.
Switch the machine off by pressing the red cover.
Symbols
The model plate on your machine can include symbols.
They contain important information regarding the use of
the machine.
Wear ear protection, goggles, and breathing mask.
Observe the applicable safety standards.
Maintenance
Warning: Make always sure that the machine is
switched off and disconnected from the power supply be-
fore you start any setting or maintenance work.
Store the machine, operating instructions and acces-
sories in a safe place. This way, the instructions and
tools are always at hand. Regularly remove dust and
dirt. Cleaning is preferably done with compressed air or
a cloth. During cleaning, wear goggles to protect your
eyes.
Utilisation
Monter et resserrer la fraise.
Ajuster la vitesse. Ajuster la butée de sortie de telle
façon qu’elle supporte le matériel coupé et qu’elle,
en même temps, produise une compensation pour le
matériel ôté.
Mettre en marche la toupie.
S’assurer que la pièce à travailler est pressée forte-
ment vers la butée.
Faire glisser la pièce à travailler d’une manière souple
de droite à gauche contre la direction de rotation de
l’outil.
Maintenir la vitesse d’avance constante. Ne pas pous-
ser trop vite pour ne pas freiner trop le moteur.
Pousser trop vite pourrait donner une mauvaise qua-
lité de coupe. En outre, il pourrait endommager le fer
de fraise ou le moteur.
Pousser trop lentement pourrait laisser des traces de
brûlure au bois.
En cas de bois très dur et de grandes coupes, il peut
être nécessaire de faire plus d’une passe lors d’un
travail progressif, jusqu’à la profondeur désirée est
obtenue.
La vitesse d’avance dépend de la taille de la fraise,
du type de matériel du bois et de la profondeur de
coupe. Il est recommandé de tester avec une pièce
de déchets pour trouver la vitesse d’avance et les
dimensions correctes.
Mettre la machine en marche en appuyant le cha-
peau rouge.
Symboles
La plaque signalétique de votre machine peut com-
prendre des symboles. Ceux-ci contiennent des informa-
tions importantes de l’utilisation du produit.
Il faut porter des protections pour les yeux et les oreilles,
et un masque respiratoire.
Il faut aussi remplir les standards de sécurité applicables.
Maintenance
Avertissement : Avant d’entreprendre des travaux de
réglage ou de maintenance, toujours s’assurer que la
machine est à l’arrêt et que la che d’alimentation est
débranchée.
Entreposer la machine, les instructions d’utilisation et les
accessoires dans un endroit sûr. De cette manière les
instructions et les outils sont toujours à portée de main.
Régulièrement enlever la poussière et les impuretés. Le
nettoyage se fait à l’air comprimé ou à l’aide d’un chiffon.
Lors du nettoyage, porter des lunettes de protection pour
protéger vos yeux.
Précautions à prendre: Ne pas utiliser de produit de
nettoyage sur les parties en matière plastique de la
table. Nous recommandons un produit de vaisselle doux
sur un chiffon humide. La machine ne doit en aucun cas
venir en contact avec de l’eau.
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HF50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HF50 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds, Fins als bijlage per email.

De handleiding is 5,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info