782177
30
Verklein
Vergroot
Pagina terug
1/164
Pagina verder
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
30 | GB
Loosen the sawband when the machine is not in

on the tension of the saw band to the machine for
the next user.



Wear suitable gloves when handling sawbands.

mounted on the machine before beginning work.
Never clean the sawband or the sawband guide
with a hand-held brush or scraper while the saw-
band is running. Resin-covered sawbands impair

      

long hair. Roll up loose sleeves over the elbows.
       
workpiece as possible when working.
 󰀩      
around the machine.


When working on narrow workpieces with manual
feed, use the push stick.
For diagonal cuts, place the saw bench in the ap-
propriate position and guide the workpiece on the
fence.
In order to cut dovetail tenons and teeth or wedges,
swivel the saw table into the plus and minus po-

For arced and irregular cuts, push the workpiece


Use a pattern for repeated arced or irregular cuts.
Insure that the workpiece does not roll when cutting
round pieces.
For safe work when transverse cutting, use the

10.1 Performing longitudinal cuts (Fig. AD)
Here, a workpiece is cut in its longitudinal direction.
Position the longitudinal fence (5) on the left side (if
possible) of the saw band, in accordance with the
desired width.
Lower the saw band guide (4) onto the workpiece.
(8.9)
Switch on the saw.
Press one edge of the workpiece against the longi-

side lies on the saw bench (7).
Slide the workpiece at an even feed rate along the
longitudinal fence (5) into the saw band.
     
against tipping at the end of the cutting process
󰀨
Attention! When processing narrower workpieces it
is essential to use a push stick.
8.10 Transverse cutting gauge (14) (optional)
(Fig. AC)
Slide lateral stop (aj) into a groove (af) in the saw
bench.
Release the grip screw (ag).
Turn the lateral stop (aj) until the desired angular
dimension has been set. The arrow on the lateral
stop indicates the set angle.
Retighten the grip screw (ag).
The stop rail (ai) can be slid against the lateral
stop (aj). To do so, loosen the knurled screws (ah)
and slide the stop rail (ai) into the desired position.
Tighten the knurled screws (ah) again.
Attention! Do not slide the stop rail (ai) too far in the
direction of the saw blade.
8.11 On/O󰀨 switch (Fig. A)
To turn the machine on, press the green button
1“ (10). Before starting sawing, wait until the saw
blade has reached its maximum speed.
󰀨
0 (10).
Attention!
When working with the machine, all protective devic-

-
ulated cover. When opening the cover, the machine
󰀨
cover.
9. Transport

when lifting it and call upon the help of another per-
son!
Use the transport equipment. Stand on the side of the
wheels. Pull the upper part of the machine towards
       

Attention! Note the high centre of gravity of the
machine.
Attention! Never use separating safety guards to
lift or transport the unit.
10. Working instructions
The following recommendations are examples of the
safe use of band saws.
The following safe working methods should be seen

      


Connect the machine to a suction unit when work-
ing in closed rooms.
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HBS400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HBS400 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 7,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info