767077
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
2
TO SET LOCK: Press lock/unlock button
(Figure 8)
so the green
locking indicator position is visible. Close door/drawer to engage
lock. Pull on door/drawer to ensure it is locked. Door/drawer is
now set in the locked position.
TO OPEN: Place the magnetic key over the area where the lock
is installed
(Figure 9).
You should hear an audible “click” when
the lock disengages. Open door. Close door/drawer to re-engage
lock.
TO DEACTIVATE FOR PERIODS OF NON-USE: Press button to
the red, unlocked position.
To Use
Wipe clean. Keep lock dry.
To Clean
To Install
4a Cabinets Open door and line up template top or side edge with
pencil mark from step 2. Press down firmly to stick adhesive
(Figure 4a).
4b Drawers— Open drawer and line up template side edge with pencil
mark from step 2. Press down firmly to stick adhesive (Figure 4b).
5
Fold template inward at dotted line and use a pencil to poke
through and mark two drill locations for catch (Figures 4a and 4b).
6
Peel paper (labeled
1B
) off template, then close door/drawer (Figure
5). Template will transfer from cabinet base to door/drawer (Figure
6).
If adhesive does not stick, remove bumpers from door or
drawer front.
TIP: You may be able to open adjacent door and ensure template
transfers.
Drawers If you have an inside panel (see page 1 Image B) on
your drawer front, the bottom of the template must be flat along
the outer panel as shown in Figure 7, or the dotted slots on the
template must be fully on the inner panel as shown in Figure 7.
If template does not fit either of these two recommended options, this
lock should not be used on your drawers.
7
NOTE: If lock is being mounted on a cabinet door with an inset
panel only the part of the template with the diagonal lines should
be overhanging the recess area of the inset panel. If any more of
the template hangs over the recess of the inset panel installation in
this location is not recommended.
Use a pencil to poke through and mark two drill locations for lock
(Figure 6).
Remove template.
8 Visually inspect marked hole locations of the lock to make sure holes
are both the same distance from edge of door/drawers.
To remove the lock, remove screws.
To Remove
89
Green = Locked Red = Unlocked
CAUTION: DO NOT DRILL THROUGH CABINET DOOR! DO NOT DRILL
THROUGH THIN INSET PANELS. Follow the drill manufacturer’s instructions
when using your drill. Power tools are not recommended for screw
installation.
9 Using a 7/64 drill bit predrill 3/8” deep holes at marked locations.
10 Position catch with flat side facing out as shown
(Figure 7 inset)
and use Phillips head screwdriver to install two screws. Position lock
as shown and use Phillips head screwdriver to install two screws
(Figure 7).
11 Test the lock. Set lock to the locked position by pushing the lock/unlock
button so the green locking indicator is visible. Close door/drawer. Place
magnetic key over area where lock is installed and open cabinet door/
drawer to ensure it can open and close easily with no interference.
7b7a
Determine Lock Placement (continued)
1B PEEL OFF
2
SCREW HOLES
FOR CATCH
FOLD
3
SCREW HOLES
FOR LOCK
4a
2
SCREW HOLES
FOR CATCH
1B PEEL OFF
3
SCREW HOLES
FOR LOCK
FOLD
2
SCREW HOLES
FOR CATCH
1B PEEL OFF
FOLD
1A PEEL OFF
1B
PEEL OFF
2
SCREW HOLES
FOR CATCH
FOLD
5
6
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
FOLD
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
FOLD
4b
7
OK OK
OK
3
SCREW HOLES
FOR LOCK
3
SCREW HOLES
FOR LOCK
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Safety 1st Complete Magnetic Locking System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Safety 1st Complete Magnetic Locking System in de taal/talen: Engels, Spaans als bijlage per email.

De handleiding is 3,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info