634238
3
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
INSTALLATION AND OPERATING
INSTRUCTIONS
INTRODUCTION
The Seafarer echo sounder operates by measuring the time interval between transmission and reception of ultra-sonic pulses from
the sea bed via a piezo electric transducer fitted in the hull of the boat.
The depth is displayed on a circular dial by a brilliant yellow Light Emitting Diode (LED) on three range scales. Ranges are
0—20m, 060m and 0200m on metric model or, 060ft, 060 metres and 0-100 fathoms on Feet/Fathoms model. In
addition, the instrument is fitted with two variable depth alarms (audible and visual) which operate between a minimum of 2.7
feet and maximum of 29 metres (nominal).
TRANSDUCER INSTALLATION
WARNING: The co-axial cable is sealed into the stem of the transducer and if damaged in any way cannot be reconnected. The
transducer lead has a nominal length of 24 feet (7.3 metres) and should not be extended or cut without the advice of a service
engineer. Any excess cable should be coiled away from excessive heat or sources of electrical interference. Transducers with
longer cable can be supplied to special order. For full depth performance the transducer stem should be mounted as near vertical
as possible. Install the transducer in a part of the hull which is as clear as possible from aerated or turbulent water and where
accidental damage is unlikely to occur. Normally a position slightly aft of amidships is preferable. For fin-keel sailing boats it
may be preferable to fully recess the transducer into the stem so that the face is completely flush. It should be remembered that
the beam angle of the transducer is ±22½
o
and care should be taken that a false echo is not created by the keel. If a single
transducer is installed on the centre line of the boat depth readings will be obtained up to an heel angle of 22½
o
. If two
transducers are required, to avoid fin-keels for instance, then each should be fitted in opposite bilges facing outward at an angle
of approximately 15
o
. By using an automatic changeover switch (optional extra) available from all good chandlers, a twin
transducer installation will enable the Seafarer 5 and 700 to give accurate depth readings to an heel angle of 37½
o
.
The following illustration indicates typical transducer installations using a wooden fairing block outside the hull. The fairing
block has been carefully bored, carved and sanded to a streamlined shape avoiding the creation of turbulent water which may
reduce or even prevent depth indication when the boat is travelling at a speed. In one of the examples shown, an internal fairing
block has been used for strength and sealing and to allow for hull curvature. The installation should be carefully rendered
watertight by using a sealing compound between all mating surfaces. Do not over-tighten the nuts on the transducer stem.
Fig 1
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw SEAFARER 700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van SEAFARER 700 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info