634238
13
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
5. Next a small amount of adhesive filler is to be mixed (Plastic Padding or similar).
IMPORTANT
The effectiveness of filler is not improved by using increased amount of hardener; therefore do not exceed the stated
amount. (If the hardener tube is used up before the large tube, then a considerable excess of hardener has been used).
DO NOT MIX MORE FILLER THAN CAN BE USED IN 5 MINUTES.
Punch a hole in the nozzle of the small tube marked “Hardener” by using the reverse side of the cap. (Do not enlarge the
hole). Squeeze out an equal length from each tube onto a piece of glass, hardboard or similar, and mix thoroughly. (See
illustration 1 and 2 on the side of the large tube).
Locate tube in the chosen position and apply filler with a knife blade in 3 or 4 places around the tube. See illustration 5.
Leave to set hard, 15 minutes approximately.
6. When the tube has set rigid, mix further filler to instructions and with a firm pressure apply to the hull around the tube. See
illustration 6. Then repeat the process around the tube itself on the previously roughened surface. See illustration 7. A further
mix is then required to complete the fixing of the tube by building up a fillet all around as shown in illustration 8.
7. Take the transducer, remove the top nut from the threaded stem taking it over the plug at the end of the co-axial cable. Place
the transducer into the tube and adjust the remaining nut level with the top of the tube. See illustration 9. Remove the
transducer from the tube and pa the co-axial plug through the inside of the top cap, and pass it over the transducer stem. Next
pass the co-axial plug through the nut previously removed and thread it down the transducer stem until it reaches the top cap,
and tighten, holding the inner nut to stop it turning. See illustration 10.
8. Pour the oil into the tube fixed to the hull so that it is not more than half full.Check that there are no oil leaks from the
moulding that joins the tube to the hull. Push the transducer SLOWLY into the tube, having first removed the self-tapping
screw from the housing cap. When the transducer is in place with the face touching the inside of the hull, replace the self-
tapping screw. Push the co-axial transducer plug firmly into the back of the Seafarer. The system is now ready for use. See
illustrations 11 & 12.
NOTES
a. By adopting the above method of in-hull echo sounding the pattern of ultrasonic sound emitted by the crystal in the
transducer remains at a p proximately 45 in a conical shape. If the transducer and its tube housing are installed vertically,
therefore, accurate depth indication will be given up to a heel angle of 22½ (dependent upon the thickness and quality of hull
material).
/continued ……
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw SEAFARER 700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van SEAFARER 700 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info