390830
8
Verklein
Vergroot
Pagina terug
1/70
Pagina verder
DESCRIPTION
1. Grinding wheel
2. Tool-less wheel guard
3. Aux. handle
4. Spindle lock button
5. Switch
6. Disc flange
7. Clamp nut
8. Spindle shaft
9. Wrench
10. Diamond blade (optional)
11. Wheel guard lock lever
12. Live tool indicator
STANDARD ACCESSORIES
Aux. handle, Wrench.
A grinding wheel is included in the standard accessories
for some countries.
APPLICATIONS
Use only for the purposes listed below:
Grinding
Cutting - for Diamond blade only (optional)
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can
exceed 85 dB (A). In this case, sound insulation and
hearing protection measures must be taken by
the operator.
SWITCH (FIG. 1)
This tool is started and stopped by sliding and
releasing the switch (5).
For the convenience for continuous operation,
slide the switch along then press the front end down
to lock it (action A).
To release the lock, press the rear end of the switch
(action B).
MOUNTING THE DIAMOND BLADE OR OTHER
FLAT WHEELS (FIG. 2A, 2C)
Attach the disc flange (6), the diamond blade/flat
wheels (10) and the clamp nut (7) upside down,
the raised part of the flange does not face to the
spindle shaft (8).
Be sure the disc flange is properly seated on the
spindle shaft.
Depress the lock button (4) located on the right side
of gear case.
Using the wrench (9) provided, tighten the clamp nut
in a clockwise direction.
MOUNTING THE GRINDING WHEEL BLADE
(FIG. 2B, 2C)
Attach the disc flange (6) and the wheel (1) on the
spindle before fitting the clamp nut.
Ensure that the wheel (1) is correctly seated over the
boss on the disc flange and clamp nut.
Depress the lock button (4) located on the right side
of gear case.
Using the wrench (9) provided, tighten the clamp nut
in a clockwise direction.
WARNING
Check carefully whether or not there are
cracks in the wheel. Replace a cracked wheel
immediately.
TOOL-LESS WHEEL GUARD
Release the wheel guard lock lever (11) then turning the
tool-less wheel guard (2) to the desired position.
The max. turning axie is 90° on either side; otherwise the
guard can’t be locked.
OPERATING (FIG. 3)
KEEP SAFETY GUARDS IN PLACE.
NEVER COVER THE AIR VENTS SINCE THEY
MUST ALWAYS BE OPEN FOR PROPER
MOTOR COOLING.
The key to efficient operating is controlling the pressure
and surface contact between the disc and work piece.
Flat surfaces are ground at an acute angle, usually 10 to
20 degrees with the work piece. Allow the disc to reach
full speed before starting to grind. Too great an angle
causes concentration of pressure on a small area which
may gouge or burn work surface.
LIVE TOOLINDICATOR
This tool features a live tool indicator (12) which
illuminates as soon as the tool is connected to the supply.
This warns the user that the tool is connected and will
operate when the switch is pressed.
5
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
EAG-8011-8012_20 lgs 10/08/05 11:19 Page 5
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ryobi eag 8012 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ryobi eag 8012 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info