167808
28
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
4. CROSSOVER SETTINGS
Now you can set an appropriate lowpass crossover fre-
quency. For this purpose, open the input gain control
- the arrow of the knob should point to "noon" - so you
can hear the subwoofer playing. Ideally, the low-pass
cut-off frequency should be set between 50 to 90 Hz - and
this setting has to be entirely determined by ear. Try to
find lowpass crossover frequency setting, that gives you
a "full-bodied" bass reproduction with enough impact in
the upper bass range.
Note: If the lowpass crossover frequency is set too low,
the sound will have a tendency to sound extremely soft
and low-end heavy!
Now you can adjust the subsonic-highpass, if you wish
to squeeze out the most (max-dB) of your subwoofer
system. Turn the highpass frequency control up, to a
point where you can hear that the bass reproduction
starts to get "thinner". The subsonic highpass frequency
should be set to a value between 20 to maximum 50 Hz.
4.2.4 ADJUSTING INPUT SENSITIVITY
To reach a maximum noise-free dynamic headroom
from each individual head unit/amplifier/speaker com-
bination, it is important to set the respective input gain
controls correctly. The input level settings determine the
actual signal-to-noise ratio, and they are also responsible
for obtaining the maximum distortion-free SPL (sound
pressure level) from your specific setup.
4.2.2 BANDPASS FOR KICKBASS
SYSTEMS
If you intend to operate a kickbass loudspeaker system in
the front doors of your vehicle, you must select two cross-
over frequencies at the active crossover of your RODEK
amplifier. The operation mode must be set to bandpass.
The bandpass filter contains a highpass (10 - 400Hz) with
a cascaded lowpass (30 - 400Hz) filter. The lowpass
crossover frequency point is usually set at a frequency
that equals at least twice the value of the highpass
crossover frequency setting. The lowpass filter is mostly
set a little lower, than the highpass crossover frequency
setting of the satellite channels.
Kickbass speaker system, front door mounted,
recommended bandpass frequencies
16 cm Kickbass Speaker System 80 - 110 Hz Highpass
200 - 250 Hz Lowpass
4.2.3 BANDPASS FOR SUBWOOFER
SYSTEMS
To drive a subwoofer system, the integrated electronic
crossover must also operate in bandpass mode. Before
you attempt to adjust the lowpass crossover frequency,
you must first turn the (subsonic)highpass frequency
control counterclockwise to its lowest position at 10 Hz.
28
R1500-4100A2 Manual.indd 28R1500-4100A2 Manual.indd 28 07.07.2004 10:59:12 Uhr07.07.2004 10:59:12 Uhr
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 4100 a bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 4100 a in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info