167808
26
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
26
3. ELECTRICAL WIRING
3.3 CONNECTION OF POWER CABLES
Run the positive power cable ("+12 V") directly from
the positive terminal of the car battery to the amplifier.
Make sure the power cable makes good contact to the
battery; i.e. use an appropriate battery clamp that ac-
cepts big gauge power cables! For protection of your car
audio system and your entire car against electrical fire
hazards from a short-circuit of the main power cable
with chassis ground, you must insert a main fuse (holder)
within the first 30cm of the battery. The fuse type/value
should be matching the limitations of your main power
cable and the requirements of your car audio system.
Preferably a minimum of 80 Amperes with this amplifier
and an appropriate power cable cross-section.
Now you route the ground cable to the amplifier. It is best
to keep the ground cable ("-12V") as short as possible,
i.e. to find a chassis contact very close to the amplifier.
The ground power cable must have the same cross-sec-
tion as the positive power cable. It is recommended to
use a corrosion-resistant gold-plated power ring or a
massive ground clamp between the ground cable and
the chassis ground point. Keep in mind that audible
interferences and problems originating in the power
supply of the amplifier, are mostly based on a bad ground
contact. So a good (and clean) grounding to the vehicle
chassis is absolutely crucial, to obtain best performance
of your amplifier.
Especially the music signal cables (RCA interconnects)
should be kept far away from any potential sources of
electrical interference i.e. electronic vehicle manage-
ment systems (engine computers, relays etc.) fuel
pumps, wiring harnesses etc.!
3.1 RCA INTERCONNECTS / REMOTE
LEAD
Carefully run the RCA audio signal interconnect(s) and
the remote switching cable from the head-unit to the
amplifier. The audio signal cables should be routed com-
pletely separate from the power cables. Use only double
or triple shielded quality cables!
Connect the remote wire lead to the remote output of the
head-unit and to the remote input terminal of the ampli-
fier. Finally connect the RCA interconnect cable(s) to the
respective outputs on the head-unit and the RCA inputs
of the amplifier.
3.2 LOUDSPEAKER CABLES
Connect the loudspeaker wires to the speaker terminals
of the amplifier. Use good quality wires of 2.5mm² cross-
section. You will need a set of Allen wrenches for the con-
nection of the wires!
When baring wires, remove approximately 6-8mm of
the insulation and after axially twisting the wires; insert
the bare ends into the corresponding speaker terminal
output on the amplifier. Be sure to follow correct polarity
("+" to "+"; "-" to "-"). Tighten the terminal screws on
the amplifier.
R1500-4100A2 Manual.indd 26R1500-4100A2 Manual.indd 26 07.07.2004 10:59:11 Uhr07.07.2004 10:59:11 Uhr
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 4100 a bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 4100 a in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info