692203
59
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
59
Problem Possible solution
Printing stops unexpectedly.
When printing from the SD card, the 3D printer must be disconnected
from your computer.
Check the settings on your computer. It must not enter standby mode
(check the power settings) or shut down (after installing software or
software updates) during printing.
The printed object does not adhere to
the print bed.
The nozzle temperature is too low. Increase the nozzle temperature.
There is residue on the print bed that is preventing the object from
sticking. Clean the print bed (see “d) Cleaning the print bed” on page
57 for details).
The print speed is too high. Select a lower print speed.
Recalibrate the print bed.
Use a raft as an aid for the printed object.
The printed object cannot be removed
from the print bed.
Wait until the printed object has cooled down.
Remove the printed object with the scraper.
Incorrect information is displayed on the
touchscreen display, or the touchscreen
display is empty.
Restart the 3D printer (see “f) Restarting the 3D printer” on page 38 ).
The nozzle cools down unexpectedly.
Go to the < Preheat > menu and select < Extruder >. Perform an
action within 5 minutes (e.g. add/remove lament or start printing).
The transport route to the nozzle is
blocked.
Always remove excess lament from the nozzle before each print.
The nozzle is blocked.
Clean the inside of the nozzle (see “b) Cleaning the nozzle” on page 56).
Remove the extruder and clean the interior (see “c) Cleaning the
inside of the extruder” on page 57).
Check whether the extruder fan is defective. If so, replace the extruder.
The extruder moves in the wrong
direction.
Check that the lament spool rotates freely on the holder.
The lament is jammed and cannot be
removed.
Load and then extract some lament.
The extruder does not heat up or carries
on heating up.
Restart the 3D printer.
Go to the < Preheat > menu. Select < Extruder > and wait for
approximately 2 minutes.
Check the nozzle temperature on the control panel.
The thermistor and heating bead are defective. Replace the thermistor
and heating bead.
The heating temperature displayed on
the control panel is 0 °C or similar to the
room temperature.
The thermistor and heating bead are defective. Replace the thermistor
and heating bead.
59

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Renkforce RF100 XL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Renkforce RF100 XL in de taal/talen: Engels als bijlage per email.

De handleiding is 7,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Renkforce RF100 XL

Renkforce RF100 XL Gebruiksaanwijzing - Nederlands - 64 pagina's

Renkforce RF100 XL Gebruiksaanwijzing - Deutsch - 62 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info