559665
5
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
Power on state: The gear motor will return to zero automatically, when the
signal of motor cannot be detected for more than 4
seconds then the gear motor’s driver will be cut off
immediately and show the E1 on the LCD display. All the
other digital and function mark are blank, and the output
signals are cut off also.
E2 (ERROR 2): When the monitor read the memory data, if the I.D. code is not correct or
the memory IC damages then the monitor will show E2 immediately at
power on.
E3 (ERROR 3): After 4 seconds by start mode, the computer detects the faulty motor did
not leave the zero point then the LCD bar displays “E3”.
LCD Workout Graphics
PRESET PROGRAM PROFILES:
PROGRAM 1 PROGRAM 2 PROGRAM 3
MANUAL ROLLING VALLEY
GB
PROGRAM 4 PROGRAM 5 PROGRAM 6
FAT BURN RAMP . MOUNTAIN
P6.
2. Press ENTER key to enter your workout program.
3. The TIME will flash and you can press UP or DOWN key to set
your exercise TIME. Press ENTER key to confirm your desired
workout TIME.
4. The DISTANCE will flash and you can press UP or DOWN keys to
set your target DISTANCE. Press ENTER key to confirm your
desired workout DISTANCE.
5. The CAL will flash and you can press UP or DOWN keys to set
your exercise CALORIES. Press ENTER key to confirm your
desired workout CALORIES.
6. Press START/STOP key to begin exercise.
Operation Instruction:
1. Plug in the power
Plug in the adaptor to the equipment then the computer will produce a beep sound
and then turn on the computer at the Manual mode.
2. Program select and setting value
. Use the PROGRAM key to select program mode and then press ENTER to
confirm your exercise mode.
. At the Manual mode, the computer would allow user to use the UP or DOWN key
to set up specific workout TIME, DISTANCE and CALORIES. Press UP + DOWN
keys can clear out the setting value to zero.
C. Press the START/STOP key to begin exercise.
D. When you reach the target, the computer will produce beep sounds and then stop.
E. If you set up more than one target and you would like to reach next target, press
START/STOP key to keep on exercise.
Operation guide:
The computer will enter CLOCK setting mode when power on it. You should set up the
current time by the UP or DOWN keys to adjust the Hours and minutes.
Clock Mode:
a. The computer will enter the clock mode when there is no signal input or no keys be
pressed after 4 minutes. You can press ENTER key to switch the clock and
temperature at the clock mode or press other keys to quit the clock mode.
b. You can set up the CLOCK by holding ENTER key for over 2 seconds then adjust by
UP or DOWN keys.
c. By holding the ENTER and UP keys together for over two seconds, you can check the
current clock at “NO SPEED” mode.
Error Message:
E1 (ERROR 1): Normal state: During workout if the computer does not receive a signal
from the motor for more than 4 seconds error 1 will be displayed,the
machine will automatically check 3 times in order to ensure this is the case.
GB
b. During the stop mode, press the key to START exercise.
c. Press this key can allow you to quickly start the computer
without selecting a program. For Manual workout only. Time
automatically begins to count up from zero
1. UP key: a. Press the key to increase the resistance during exercise mode.
b. During the setting mode, press the key to increase the value of Time,
Distance and Calories.
2. DOWN key: a. Press the key to decrease the resistance during exercise mode.
b. During the setting mode, press the key to decrease the value of Time,
Distance, and Calories.
3. ENTER key: a. During the setting mode, press the key to accept the current data
entry.
b. At the stop mode, by holding this key for over two seconds the
computer will re-power on and all the value will reset to zero.
c. During the START stage, press the key to exit the auto-scan
mode to manual-scan mode. .
4. PULSE RECOVERY key: Press the key to activate heart rate recovery function.
5. PROGRAM key: Press the key to select the program from P1 to P6.
Program Introduction & Operation:
Manual Program: Manual
P1 is a manual program. User can start exercise by pressing START/STOP key. The
default resistance level is 3. Users may exercise in any desirous of resistance level
(Adjusting by UP/DOWN keys during the workout) with a period of time or a number
of calories or a certain distance.
Operations: 1. Press the ENTER key to enter MANUAL (P1) program.
2. The TIME will flash and you can press UP or DOWN key to set
your exercise TIME. Press ENTER key to confirm your desired
workout TIME.
3 The DISTANCE will flash and you can press UP or DOWN keys to
set your target DISTANCE. Press ENTER key to confirm your
desired workout DISTANCE.
4 The CAL will flash and you can press UP or DOWN keys to set
your exercise CALORIES. Press ENTER key to confirm your
desired workout CALORIES.
5 Press START/STOP key to begin exercise.
Preset Program: Rolling, Valley, Fat Burn, Ramp, and Mountain Program
PROGRAM 2 to PROGRAM 6 is the preset programs. Users can exercise with
different level of resistance in different intervals as the profiles show. Users may exercise
at any level of resistance level (Adjusting by UP/DOWN key during the workout)
with a period of time or a number of calories or a certain distance.
Operations: 1. Use PROGRAM key to select one of the above programs from P2 to
GB
17
18 19
16
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Reebok Edge Bike bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Reebok Edge Bike in de taal/talen: Engels als bijlage per email.

De handleiding is 3,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info