587563
7
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
7
Infrared-remote control
All settings can also be made using an infrared remote
control (optional with RKL 220). A description of the but-
ton functions (see picture below) can be found in the
“Control panel” section. The remote control’s range is
approximately 5 m.
Power is provided by two 1.5 V AAA batteries. (supplied
with the remote control)
Operating Mode
Adjusting the direction of the outgoing air
The device is equipped with vertical and horizontal plate
fins that can be adjusted for various conditions.
7 "FULL-TANK" display (Water tank full)
When the water tank is full, the "FULL TANK" and
"MODE" displays blink and an alarm goes off. The
compressor automatically switches off. After the wa-
ter tank on the right side of the unit has been emp-
tied and replaced, the unit switches back to auto-
matic operation.
8 "COMP. ON" display (compressor is running)
When the compressor is started again for a second
time, a minimum of three minutes must elapse be-
forehand for safety reasons. During this time, the
"COMP ON" display blinks.
9 "TIMING ON" display
If this display is lit up, the unit will automatically be
switched on after a preset amount of time.
10 "TIMING OFF" display
If this display is lit up, the unit will automatically be
switched off after a preset amount of time.
11 Operating mode and fan setting display
This display provides information about the operat-
ing mode and the fan setting which have been se-
lected.
12 REMOTE-SENSOR (sensor remote control)
The unit receives the signals sent from the infrared
remote control (special accessory for RKL 220) via
the "REMOTE SENSOR".
POWER
on / off
THERMO
CONTROL
MODE
TIMER
AUTO
SWING
reset
set
1
4
2
5
6
1. Switch the unit on with the "On / Off”
button
2. Set the target temperature using the
arrow buttons.
3. Select the fan setting (AUTO, HI, MED
or LO) with the "MODE" button.
1. Set up the device in the room to be de-
humidified.
2. Do not extend the exhaust hose to the
outside.
The warm air remains in the room, thus
increasing the water absorption of the air.
3. Switch the unit on with the "On / Off”
button.
4. Set the lowest target temperature 20°C
using the arrow buttons.
5. Select the lowest fan setting LO with
the "MODE” button.
1. Switch the unit on with the "On / Off”
button.
2. Set the FAN operating mode with the
"MODE” button.
The exhaust hose does not need to be
connected in circulation mode.
1. Press the "AUTO SWING" button.
The vertical plate fins slowly move
back and forth to automatically distrib-
ute air.
2. Press the "AUTO SWING" button again
to adjust the fixed output direction.
The plate fins stay in the last position
they reached.
Never adjust the vertical plate fins
manually!
Adjusting the vertical plate fins:
1. Using the two adjustment levers,
manually adjust the horizontal plate
fins between the vertical plate fins.
Adjusting the horizontal plate fins:
Cooling
Ventilation (circulation)
Dehumidifying
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO RKL220 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO RKL220 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO RKL220

REMKO RKL220 Gebruiksaanwijzing - Nederlands - 16 pagina's

REMKO RKL220 Gebruiksaanwijzing - Deutsch - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info