490687
13
Verklein
Vergroot
Pagina terug
1/90
Pagina verder
13
8.1 Smooth start-up
After switching on the machine, regulation elec-
tronic circuits provide for a smooth start-up up to
the operating speed without unnecessary kicks.
This decreases the wear of gears, and increases
machine lifetime.
8.2 Limitation of start-up current
The electronically controlled smooth start-up en-
sures that the machine starts up without a kick.
Due to limited start-up current of the machine, a
protection rating of 10 A is suf cient.
8.3 Overload protection
Is the tool overloaded, the oveload protection is
actuated, and the tool stops. When the load is
removed, the tool restarts automatically. Before
you continue in your work, you should let the tool
reach full speed.
8.4 Thermal overload protection
If you work with the tool for longer periods of
time under excessive load conditions, the motor is
switched off by the thermal protection that protects
the motor from overheating.
After having cooled down, i.e. after about 30 sec-
onds, the machine can be restarted again.
Causes of overheating: excessive pressure, de-
viation of tool from perpendicular position, bad
quality or excessive wear of disc.
9 Maintenance
- The unit should be stored in a dry place where
it is protected against freezing.
- The ventilation holes on the motor casing must
not get blocked up.
- The cable may only be replaced in a specialised
electrical workshop quali ed to perform such
work.
After approx. 200 hours of use the following main-
tenance work must be performed:
- Check the length of the brushes. Brushes shorter
than 5 mm should be replaced.
- The machine turns itself off automatically when
the brushes are worn out. The machine must be
sent to a service centre for maintenance.
WARNING
To preserve the protection class the machine
must undergo a safety inspection; this must
be done in a specialised electrical workshop
quali ed to perform such work.
- Service – see enclosed sheet.
10 Environmental Protection /
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into house-
hold waste!
According to the European Directive 2002/96/EC
on waste electrical and electronic equipment and
its incorporation into national law, power tools that
are no longer suitable for use must be separately
collected and sent for recovery in an environmen-
tal-friendly manner.
REACh
REACh is a European Chemical Directive that
came into effect in 2007. As “downstream users”
and product manufacturers, we are aware of our
duty to provide our customers with information.
We have set up the following website to keep you
updated with all the latest news and provide you
with information on all the materials used in our
existing products:
http://www.tts-protool.com/reach
11 Warranty
For our tools, we give warranty for material and
production defects in accordance with the locally
applicable legal provisions, but in any case for at
least 12 months. Within the EU member states, the
warranty period is 24 months (veri cation through
invoice or delivery note).
Damage caused by, in particular, natural wear,
overloading, incorrect handling, or damage caused
by the operator, or damage caused through use of
the equipment contrary that speci ed in the Oper-
ating Instructions, or damage which was known at
the time of purchase, is not covered by the war-
ranty. Furthermore, damage caused by the use of
non-original PROTOOL accessories and consumable
material (e.g. sanding pads) is also excluded.
Complaints can only be recognised if the tool is
returned while still assembled to the supplier or an
authorised PROTOOL Customer Service workshop.
Keep the Operating Instructions, Safety Instruc-
tions, Spare Parts List and purchase receipt in a
safe place. Otherwise the respective, current war-
ranty condi tions of the manufacturer shall apply.
Note
Due to continuous research and development work,
we reserve the right to make changes to the tech-
nical content of this documentation.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool WCP50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool WCP50 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info