645073
6
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
POWX1420 EN
Copyright © 2016 VARO P a g e | 6 www.varo.com
7.2 Depth adjustment (Fig. 7)
Loosen the cutting depth setting clamp (9) by lifting the lock lever.
Hold the base plate (14) flat against the body of the work piece and lift the body of the saw
until the blade is at the right depth.
Tighten the depth locking lever.
7.3 Angle adjustment (Fig. 8)
Loosen the lock lever knob for angle adjustment (11).
Adjust the base plate (14)(to the desired angle between 0° to 45°.
Tighten the lock lever knob for angle adjustment (11).
Note: for best cutting results, always ensure that saw blade protrudes no
more than 3 mm below the bottom surface of the workpiece.
7.4 General cut
Mark a cutting line on the workpiece.
Rest the front part of the shoe flat on the workpiece surface with the blade not making any
contact with the workpiece.
Switch on the tool and allow it to reach its full speed.
Align the saw blade with the cutting line on the workpiece, gently push the saw forward.
Never force the saw but maintain a light and continuous pressure when completing the
cut. Switch off the tool only after the tool is completely away from the workpiece When the
cutting is interrupted, resume the cut by allowing the blade to reach full speed and then re-
entering the cut slowly
When cutting across the grain, the fibres of the wood will have a tendency to lift and tear,
moving the saw slowly to minimize this effect.
Note: there are two notches on the front edge of the shoe as an aid for
alignment. When making a 45° bevel cut, just align the left notch marked
with 45° with the cutting line on the workpiece. For a straight 90° cut, align
the right notch marked with with the cutting line on the workpiece. For
precise cutting, always make a trial cut before carrying out operation
7.5 Pocket cutting
Disconnect the plug from the power supply before making any adjustments. Set the depth
adjustment based on the thickness of the line drawing for the cut .raise the lower guard by
using the lift lever.
With the blade barely above the material to be cut, start the saw and allow the blade to
come to full speed. Gradually lower the blade unto the material to be cut using the front
end of the shoe as a pivot point. When the blade starts cutting, release the lower guard.
When the shoe is resting flat on the surface being cut, proceed cutting in a forward
direction to the end of the cut. Allow the blade to come to a full stop before removing it
from the cut. Never pull the saw backward since the blade will climb out of the cut and
kickback will occur. Turn the saw around and finish the cut in a normal manner, sawing
forward. Use a jigsaw or a hand saw to finish the cut in the corners, if required.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX1420 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX1420 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX1420

Powerplus POWX1420 Gebruiksaanwijzing - Nederlands - 10 pagina's

Powerplus POWX1420 Gebruiksaanwijzing - Deutsch - 10 pagina's

Powerplus POWX1420 Gebruiksaanwijzing - Français - 10 pagina's

Powerplus POWX1420 Aanvulling / aanpassing - Alle talen - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info