676177
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
POWX0026LI EN
Copyright © 2017 VARO P a g e | 8 www.varo.com
NOTE: If the battery does not fit properly, disconnect it and confirm that the battery pack is the
correct model for this charger as shown on the specification chart.
Do not charge any other battery pack or any battery pack that does not securely fit the charger.
1. Frequently monitor the charger and battery pack while connected.
2. Unplug the charger and disconnect it from the battery pack when finished.
3. Allow the battery pack to cool completely before using it.
4. Store the charger and battery pack indoors, out of reach of children.
NOTE: If battery is hot after continuous use in the tool, allow it to cool down to room
temperature before charging. This will extend the life of your batteries.
8.2 Removal / insertion of battery (Fig. 3)
WARNING: Before making any adjustments ensure the drill is switched off with the direction of
rotation selector (6) in the centre position.
1 Hold the drill with one hand and the battery pack (7) with the other.
2 To install: pull and slide battery pack into battery port, make sure the latch (8) on the
both side of the battery snap into place and battery is secure before begging operation.
3 To remove: use your thumb and fingers, press the battery release latches in and pull
the battery pack off at the same time.
8.3 Switch On/Off (Fig. 4 & 5)
The drill is started and stopped by depressing and releasing the ON/OFF switch trigger (5).
This cordless drill is equipped with an electric brake, when the ON/OFF switch trigger is
released completely the chuck stops immediately.
8.3.1 Rotation (right/left/lock)
Direction of rotation is controlled by the direction of rotation selector (4) located above the
switch trigger.
Right: To select forward rotation, release the on/off switch and push the forward/reverse lever
to the left side of the tool.
Left: To select reverse rotation, push the lever to the right side of the tool.
Lock: When the selector is in the centre position, the switch trigger is locked. (See Fig. 5)
This helps to reduce the possibility of accidental starting when not in use.
8.3.2 Variable speed
This tool has a variable speed switch that delivers higher speed and torque with increased
trigger pressure. The rotational speed is controlled by the amount of switch trigger depression.
8.4 Installing and Removing a Bit and a Drill (Fig. 6)
This drill has a keyless chuck (1) to prevent the bit or drill from loosening.
1 Hold ring A of the drill chuck tight with one hand.
2 Turn upper ring B anticlockwise with the other hand until the drill chuck opening is large
enough to accept the tool.
3 Insert the drill or the screwdriver bit into the drill chuck.
4 Turn ring B clockwise until the tool is clamped tightly.
Remove the tool in the opposite way.
8.5 Adjusting the torque
The torque is adjusted by rotating the torque setting ring (2); the torque is greater when the
torque setting is set on a higher position. The torque is less when the torque setting ring is set
on a low position. Position 1 denotes the lowest and “ ” denote the highest.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX0026LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX0026LI in de taal/talen: Engels als bijlage per email.

De handleiding is 0,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX0026LI

Powerplus POWX0026LI Gebruiksaanwijzing - Nederlands - 13 pagina's

Powerplus POWX0026LI Gebruiksaanwijzing - Deutsch - 14 pagina's

Powerplus POWX0026LI Gebruiksaanwijzing - Français - 13 pagina's

Powerplus POWX0026LI Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info