675214
7
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
POWP6050 EN
Copyright © 2018 VARO P a g e | 7 www.varo.com
Repeat the procedure at the other side.
CAUTION: Dust may cause respiratory problems. Certain laminated board
materials are carcinogenic. After work, always remove all dust from the
machine.
7.7 Using the dust exhaust connection
The dust exhaustion outlet (14) shall be connecting together with an external vacuum
cleaner to take away the dust in dust cover.
If necessary, place an adapter on the dust exhaust.
8 OPERATION
8.1 Cutting in several operations (Fig. 7)
The length-stop turret (9) can be used to set different depths.
For cutting in depth and in stages, use the length-stop turret (9) as an aid. Using the depth
stop set the desired depth to the lowest depth-stop position on the turret. Rotate the turret so
that the highest point is under the depth stop and execute the first cut. Repeat the cut with the
second-highest setting and finally with the last setting. You can also use two positions if the
desired depth is reached in two operations.
8.2 Switching on and off (Fig. 8-9)
Connect the plug to the power supply.
To switching the tool on, you press lock-off button (12), then press on/off switch trigger
(11) to switch on the tool.
To switch the tool off, release the ON/OFF switch trigger (11) or in case of continuous use,
shortly press ON/OFF switch trigger (11) again.
To adjust the cutting speed, turn the speed control dial (2). Position 1 denotes the lowest
speed. Position 6 denotes the highest speed. Turn the knob to increase or decrease the
speed. The smaller the cutter head, the higher the speed. The larger the cutter head, the
lower the speed. A cutter head which runs too fast causes scorching of the work-piece and
leaves burnt marks.
CAUTION: Do not change the speed when the machine is working under
load.
8.3 Cutting direction
Always observe the safety instructions and applicable regulations.
Always move your router as indicated in below Fig. 10 (outer edges/inner edges).
To prevent the cutter head from jumping and to obtain a good result, carry out exterior
cuts in anticlockwise and interior cuts in clockwise direction.
NOTE: Check that the cutter is correctly installed in the collet.
Place the machine on the workpiece before switching on.
Select the optimal speed using the speed control dial.
Set the cutting depth.
For greater cutting depths it is recommended to make shallow cuts.
Connect a dust cover.
Make sure the locking lever is always locked before switching on.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWP6050 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWP6050 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWP6050

Powerplus POWP6050 Gebruiksaanwijzing - Nederlands - 10 pagina's

Powerplus POWP6050 Gebruiksaanwijzing - Deutsch - 11 pagina's

Powerplus POWP6050 Gebruiksaanwijzing - Français - 10 pagina's

Powerplus POWP6050 Aanvulling / aanpassing - Alle talen - 7 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info