481008
10
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
POW8041 EN
Copyright © 2014 VARO P a g e | 10 www.varo.com
7.2.4 90° cross-cuts and 0°-45° rotary table (Fig. 10)
The POW 8041 can be used to make angled cuts of 0°-45° relative to the stop rail on the left
and right side.
Undo the rotary table (8) by slackening the two locking screws (10) on the stop rail (7).
Turn the rotary table (8) by its handle (2) to the angle you want, i.e. the mark (a) on the
rotary table has to comply with the required angle dimension (11) on the stationary base
plate (9).
Re-tighten the lock screw (1 ) to fasten the turntable (8).
Make the cut as described in Section 7.2.3.
7.2.5 Mitre cuts 0a-45D and rotary table 0* (Fig. 11/12)
The POW8041 can be used to make mitre cuts of 0°- 45'* relative to the machine bed on the
left side.
Lift the machine head to its top position.
Fix the rotary table (8) in 0° position.
Use the hexagon wrench (19) to undo the clamping screw (22) and tilt the machine head
by its handle (2) to the left until the mark (a) on the machine head points to the required
angle dimension (b).
Re-tighten the clamping screw (22) and make the cut as described in Section 7.2.3.
7.2.6 Mitre cuts 0°-45* and rotary table 0fl-45fl (Fig. 11/13)
The POW8041 can be used to make mitre cuts on the left at an angle of 0°- 45°" relative to
the work top and 0^- 45° relative to the stop rail (double mitre cuts).
Lift the machine head to its top position.
Release the turntable {8) by slackening the lock screw (10) on the stop rail (7).
Adjust the rotary table (8) by its handle (2) to the required angle (see also Section 7.2.4).
Re-tighten the lock screw (10) to fasten the turntable.
Undo the clamping screw (22) and tilt the machine head (4) by its handle (2) to the left to
the required angle dimension
(see also Section 7.2.5).
Re-tighten the clamping screw (22).
Make the cut as described in Section 7.2.3.
7.2.7 Chip extractor (Fig. 12)
The saw is equipped with a chip extraction socket (3D.
It is easy therefore to connect the machine to a chip extraction system.
8 REPLACING THE SAW BLADE (FIG. 14/15)
Pull out the power plug. The blade must slop moving completely.
Concert the saw to mitre box saw mode (see also Section 8.2.1).
Slacken the two Allen screws (32) and take off the splitter (30) together with the blade
guard (17).
Remove the recessed head screws (33) and the table insert (34).
Use the supplied face wrench (21) to lock the outer flange in place and use the socket
wrench (19) to unscrew the hex screw (Important: left-hand thread. Unscrew clockwise!).
Take the saw blade (5) off the inner flange and lift up and out through the slot in the saw
table (16}.
Thoroughly clean the outer and inner flange and the motor shaft before inserting and
securing the new blade.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POW8041 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POW8041 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POW8041

Powerplus POW8041 Gebruiksaanwijzing - Nederlands - 13 pagina's

Powerplus POW8041 Gebruiksaanwijzing - Deutsch - 14 pagina's

Powerplus POW8041 Gebruiksaanwijzing - Français - 14 pagina's

Powerplus POW8041 Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info