RESUME / HOLD
RESUME - continuing from where you have stopped
You can store the last position played. When restarting, playback will continue
from where you have stopped (RESUME). Use the OFF-RESUME-HOLD slider on
the set for this function.
1 Switch the slider to RESUME during playback to
activate RESUME.
2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback
➜Playback continues from where you have
stopped.
•To deactivate RESUME, switch the slider to OFF.
Helpful Hints:
– For MP3-CD, as it contains large amount of compressed information, resume
function will work only before the set is completely shut off.
HOLD- locking all buttons
You can lock the buttons of the set. When a key is pressed, no action will be exe-
cuted. With HOLD activated, you can avoid accidental activation of other func-
tions.
• Switch the OFF-RESUME-HOLD slider to HOLD to
activate HOLD
➜ HOLd is displayed briefly.
➜ All buttons are locked and no action will be
executed when you press any button on the set.
If the set is switched off, HOLd appears when
2; is pressed.
•To deactivate HOLD, switch the slider to OFF
➜ All the buttons are unlocked.
ESP, POWER SAVE MODE
With a conventional portable CD player, you might have experienced that music
stopped (e.g. when you were jogging). The Electronic Skip Protection prevents
playback interruption caused by light vibrations and shocks. Continuous playback
is ensured. However, ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by
dropping!
The power save mode helps to extend battery service
life for longer playback.
• Press ESP once or twice during playback.
➜ ESPappears when shock protection is activated
•To deactivate the shock protection and enter the
power save mode, press ESP again.
➜ ESP disappears.
100
SEC MAGIC ESP!
Average playing times when ESP skip protection activated :
Seconds track type
100 MP3 (128kbps)
45 Audio CD
Helpful Hints:
– For a MP3 CD,
ESP is by default always activated.
TROUBLESHOOTING
WARNING: Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
• Check that your batteries are not empty, that they are inserted correctly, that
the contact pins are clean.
•Your adapter connection may be loose. Connect it securely.
The indication nO diSC or nO AF is displayed/CD cannot be read
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens have steamed up, wait a few minutes until the lens clear up.
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication HOLd is on and/or there is no reaction to controls
• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few sec-
onds.
Music files do not play
• Check that the file names of MP3 files end with .mp3.
TROUBLESHOOTING
Some directories missing on MP3 CDs
• Check that the total number of files and albums on your MP3 CDs
does not exceed 350.
• Only albums with MP3 files are shown.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
•
Shuffle or program is active. Switch off whichever is on.
Music skips or popping sounds when you play a MP3 track
• Play the music file in your computer. If the problem remains,
encode the audio track again and make a new CD.
No sound or bad sound quality
• Playback on pause. Press 2;.
• Loose, wrong or dirty connections. Check and clean connections.
•Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check the player's position and connections.
Also keep away from active mobile phones.
CAUTION
Use of controls or adjustments or performance of
procedures other than herein may result in unsafe oper-
ation.
